GM 19133288
Axle Cover, Rear

To remove the rear axle housing cover and gasket; first, lift up the vehicle and empty the rear axle. Removed the rear axle housing cover bolts and thrown out the bolt from the rear axle housing cover and take off the rear axiom housing cover out of the axle housing that and catch the oil into drain pan contract the rear axle housing and cover back and take out the gasket material. Next, install the new gasket and the rear axle housing cover. It is important not to reuse the rear axe housing cover blocks. Instead, install new bolts for the rear axle housing cover and screw them crosswise to 40 nm (30 ft. Lbs.). Finally, fill the rear axle with the right fluid and lower the car.

To remove the rear axle housing cover and gasket; first, lift up the vehicle and empty the rear axle. Removed the rear axle housing cover bolts and thrown out the bolt from the rear axle housing cover and take off the rear axiom housing cover out of the axle housing that and catch the oil into drain pan contract the rear axle housing and cover back and take out the gasket material. Next, install the new gasket and the rear axle housing cover. It is important not to reuse the rear axe housing cover blocks. Instead, install new bolts for the rear axle housing cover and screw them crosswise to 40 nm (30 ft. Lbs.). Finally, fill the rear axle with the right fluid and lower the car.

Raising the vehicle allows you to drain the rear axle prior to cover and gasket replacement of the rear axle housing. Relocate the rear axle housing cover bolts before you dispose of them. Following that, remove the rear axle housing cover from the axle housing while collecting the oil in a drain pan and scraping away all gasket material from both components. Install the rear axle housing cover using a new gasket by avoiding the use of any rear axle housing cover bolts. New rear axle housing cover bolts should be installed followed by a crosswise torque pattern to 40 nm (30 ft. Lbs.). Before you finish install the correct fluid into the rear axle and bring down your vehicle.

Raising the vehicle with proper tools and draining the rear axle is the first step to perform this task. Cut the rear axle housing cover bolts for disposal before disconnecting the rear axle housing cover from the housing well while collecting oil in a drain pan to remove gasket material from inside and outside the housing cover. The replacement process begins with applying the new gasket while you install the rear axle housing cover according to the Fastener Notice in Service Precautions. Cover the new axle housing with fresh bolts while tightening them across the pattern using 40 Nm (30 ft. lbs.) torque and avoid using the previous bolts. The correct fluid needs to be placed into the rear axle before lowering the vehicle.

Raising the vehicle allows you to drain the rear axle prior to cover and gasket replacement of the rear axle housing. Relocate the rear axle housing cover bolts before you dispose of them. Following that, remove the rear axle housing cover from the axle housing while collecting the oil in a drain pan and scraping away all gasket material from both components. Install the rear axle housing cover using a new gasket by avoiding the use of any rear axle housing cover bolts. New rear axle housing cover bolts should be installed followed by a crosswise torque pattern to 40 nm (30 ft. Lbs.). Before you finish install the correct fluid into the rear axle and bring down your vehicle.

The first step of successful rear axle housing cover and gasket replacement begins with vehicle elevation followed by draining the rear axle. First, discard the rear axle housing cover bolts before you remove the rear axle housing cover from the axle housing while draining the oil into a container and scraping away gasket residue from both rear axle housing parts. After gathering the new gasket mount the rear axle housing cover to its position. Motorists should avoid using prior rear axle housing cover bolts; they should keep them aside while installing new bolts with a crosswise pattern to 40 nm (30 ft. Lbs. Torque. The proper fluid should be added into the rear axle before finishing by lowering the vehicle.

Vehicle professionals should begin rear axle housing cover and gasket replacement by both raising the vehicle and draining the rear axle lubricant using proper replacement methods specific to the axle type. Starting with the bolt removal of the rear axle housing cover you need to discard these screws before you can take off the rear axle housing cover into a drain pan to collect any oil leakage then wipe gasket material from both the rear axle housing and the cover. Position the new gasket along with the rear axle housing cover while avoiding the use of any used bolts for reinstallation. Utilize new rear axle housing cover bolts and secure them by tightening them in a crisscross pattern to 40 n.m (30 lb ft). The correct fluid should fill the rear axle before you lower the vehicle.

The first step to change the rear axle housing cover and gasket involves vehicle elevation while draining the axle. Use a drain pan to collect oil from the axle housing when you remove the rear axle housing cover bolts and proceed with removing each bolt for disposal. Next extract the rear axle housing cover from the axle housing while cleaning away gasket material that currently exists on both parts. The procedure starts with applying the new gasket followed by the rear axle housing cover installation according to the fastener notice in service precautions. Place new rear axle housing cover bolts and crosswise tighten them to 40 nm (30 ft. Lbs.) while avoiding the use of previously installed bolts. Rain in appropriate fluid into the rear axle before lowering the car down.

Raising the vehicle allows you to drain the rear axle prior to cover and gasket replacement of the rear axle housing. Relocate the rear axle housing cover bolts before you dispose of them. Following that, remove the rear axle housing cover from the axle housing while collecting the oil in a drain pan and scraping away all gasket material from both components. Install the rear axle housing cover using a new gasket by avoiding the use of any rear axle housing cover bolts. New rear axle housing cover bolts should be installed followed by a crosswise torque pattern to 40 nm (30 ft. Lbs.). Before you finish install the correct fluid into the rear axle and bring down your vehicle.