Make sure this part fits

GM 10273068
Emblem, Front

1997-2005 GM

Customer Questions & Expert Answers (17)
GM 10273068 Emblem, Front
GM 10273068 Emblem, Front
  • Part Description
    Emblem, Radiator Grille And Front End Ornamentation
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    1997-2005 Buick CenturyCustom, Limited, Special Edition6 Cyl 3.1 L GAS
    1997-2004 Buick Regal25th Anniversary Edition, GS, GSE, LS, LSE6 Cyl 3.8 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10273068 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10273068 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace or repair a front emblem on Buick Century? Posted by Customer
    A:
    Before putting in the new nameplate tape off both the mount surface and the replacement itself to help align the parts during assembly. Apply the J 25070 Heat Gun (J 25070) in circular motions for 30 seconds to heat the nameplate. Use a plastic flat blade to gently take off the nameplate from its surface. Use 3M Scotch Brite molding adhesive remover disk P/N 07502 or equivalent to clean adhesive from body panels while using VMP naphtha or isopropyl alcohol mixture with water on plastic panels. Use clean dry space for installation and apply tape on unmarked location before placing Buick or Regal door nameplate at 30 mm (1.188 in) below molding top and 80 mm (3.156 in) from door front edge. Position the CENTURY LIMITED nameplate directly into its designated spot in the door panel opening. Preheat the mounting area to 80-105°F (80-105°F) using the J 25070 Heat Gun (J 25070) but keep the nameplate surface at 85-90°F temperature during application. Position the label following position marks before stripping off the liner backing. Apply steady pressure to even bond the nameplate with the designated surface. Take off the protective tape from the installed area.
    Posted by ChevyPartsGiant Specialist
    Q:
    How should the installation area be prepared for the 2002 Buick Century? Posted by Customer
    A:
    Clean the installation area with the same cloth and solution, ensuring it is thoroughly dried.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be done after removing the emblem/nameplate for the 2001 Buick Century? Posted by Customer
    A:
    Eliminate all adhesive using the appropriate methods for body and plastic panels.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What temperature should the emblem/nameplate be for the 2001 Buick Century? Posted by Customer
    A:
    Ensure the emblem/nameplate is around 29-32°C (85-90°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the adhesive foam tape be applied for the 2000 Buick Century? Posted by Customer
    A:
    Apply it to the back of the emblem/nameplate and press it in place.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What tool should be used to lift or remove the emblem/nameplate for the 2000 Buick Century? Posted by Customer
    A:
    Use a plastic, flat-bladed tool to lift or remove the emblem/nameplate from the panel surface.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be used for adhesive removal on plastic panels for the 2001 Buick Regal? Posted by Customer
    A:
    A lint-free cloth with Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What temperature should the mounting surface and emblem/nameplate be heated to for the 2005 Buick Century? Posted by Customer
    A:
    Heat the mounting surface to approximately 27-41°C (80-105°F) and ensure the emblem/nameplate is around 29-32°C (85-90°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What are the positioning requirements for the GS emblem/nameplate for the 2003 Buick Century? Posted by Customer
    A:
    It should be positioned 85.725 mm (3.375 in) from the bottom edge and 31.750 mm (1.250 in) from the right edge of the rear compartment lid.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2000 Buick Regal? Posted by Customer
    A:
    Heat it with the Heat Gun (J 25070) in a circular motion for about 30 seconds.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be avoided when handling the nameplate for the 2002 Buick Regal? Posted by Customer
    A:
    Touching the adhesive backing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What temperature should the mounting surface be heated to during installation for the 2003 Buick Regal? Posted by Customer
    A:
    The mounting surface should be heated to approximately 27-41°C (80-105°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What temperature should the mounting surface be heated to for the 2004 Buick Regal? Posted by Customer
    A:
    Approximately 27-41°C (80-105°F).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What should be avoided when handling the emblem/nameplate for the 2001 Buick Regal? Posted by Customer
    A:
    Avoid touching the adhesive backing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    What is the final step in the installation process for the 2001 Buick Regal? Posted by Customer
    A:
    Remove the protective tape from the mounting surface after pressing the emblem/nameplate firmly in place.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    Q:
    How should the emblem/nameplate be heated for the 2001 Buick Regal? Posted by Customer
    A:
    Use a Heat Gun (J 25070) in a circular motion for about 30 seconds.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Emblem
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Emblem, Front 10273068 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10273068 Emblem, Front is available in the market under the name GM Emblem. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10273068 Emblem, Front fits certain Buick Regal, Century models.
The original GM component designated by manufacturer part number 10273068 maintains top performance when functioning as the Emblem, Radiator Grille And Front End Ornamentation unit at its Front. The component 10273068 is constructed from durable material and its dimensions span 3.8 x 3.6 x 0.2 inches while weighing 0.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 10273068 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.