Make sure this part fits

GM 25974060
Front Mount

2008-2010 GM

Customer Questions & Expert Answers (16)
GM 25974060 Front Mount
  • Part Description
    Mount, Engine Mount Dampening; Engine Mount Bracket; Motor Mount
  • Replaces
    25877466
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2010 Chevrolet CobaltSS4 Cyl 2.0 L GAS
    2008-2010 Chevrolet HHRSS, SS Panel4 Cyl 2.0 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25974060 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25974060 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after repositioning the underhood electrical center for the 2009 Chevrolet HHR? Posted by Customer
    A:
    Connect the wiring harness to the tray bracket and install the electrical center nuts and bolt.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after removing the bolts for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Slowly lower the transmission enough to remove the transmission mount from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be done after tightening the bolts for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Remove the floor jacks from under the oil pan.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the final step after completing the installation for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is important to remember when starting the engine mount to bracket bolts for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    The engine mount to bracket bolts must be hand started without prying the engine mount to align the holes.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after removing the engine mount for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Take out the engine mount bracket to engine bolts and then remove the engine mount bracket itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the first step for installation for the 2010 Chevrolet Cobalt? Posted by Customer
    A:
    Install the transmission mount to the mid-rail and hand start the transmission mount to mid-rail bolts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after supporting the powertrain assembly for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Loosen the transaxle mount to transaxle bolts and the engine mount to bracket bolts, then reposition both floor jacks to create a 1/8 inch gap between the mount and bracket.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What should be removed after supporting the engine for the 2010 Chevrolet HHR? Posted by Customer
    A:
    Remove the engine mount to bracket bolts and the engine mount to side rail nuts, then take the engine mount out of the engine compartment.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after removing the engine mount for the 2009 Chevrolet HHR? Posted by Customer
    A:
    Take out the engine mount bracket to engine bolts and then remove the engine mount bracket itself.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the final step after shaking the powertrain for the 2010 Chevrolet HHR? Posted by Customer
    A:
    Raise the vehicle again and tighten the rear transaxle mount through bolt to 100 Nm (74 lb ft), then tighten the front transaxle mount through bolt to 100 Nm (74 lb ft) before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    How should the new engine mount be installed for the 2009 Chevrolet HHR? Posted by Customer
    A:
    Place the engine mount onto the side rail studs, ensuring to follow fastener precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What is the sequence for tightening the engine mount bracket bolts for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Tighten in the following sequence: upper rear, lower rear, and forward.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount Bracket
    Q:
    What is the final step after tightening the bolts for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    How should the engine be supported during the replacement for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Support the engine with a hydraulic floor jack, using a piece of wood between the jack and the oil pan.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Front Mount 25974060 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25974060 Front Mount is available in the market under the name GM Engine Mount, Motor And Transmission Mount, Engine Mount Bracket. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25974060 Front Mount fits certain Chevrolet Cobalt, HHR models.
The original GM component designated by manufacturer part number 25974060 maintains top performance when functioning as the Mount, Engine Mount Dampening; Engine Mount Bracket; Motor Mount unit. The component 25974060 is constructed from durable material and its dimensions span 6.1 x 6.1 x 11.3 inches while weighing 4.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Mount; Mount, Engine Mounting. The part 25974060 has available replacement options 25877466. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.