Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 15149543
Front Mount, Driver Side

1994-2003 GM

Customer Questions & Expert Answers (8)
GM 15149543 Front Mount, Driver Side
  • Part Description
    Mount Assembly-Engine; Engine Mount Bracket; Motor Mount
  • Position
    Driver Side
  • Replaces
    15967993
  • Manufacturer
    General Motors
Make sure this part fits
$41.93 MSRP: $71.39
You Save: $29.46 (42%)
Ships in 1-3 Business Days
1
ADD TO CART
  • 1997 Chevy S10 Front Mount, Driver Side Diagram for 15149543
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 15149543

  • Vehicle Fitment

    Year Make Model Trim Engine
    1994-2003 Chevrolet S10Base, LS, Xtreme4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS
    1994-2003 GMC SonomaSL, SLE, SLS4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 15149543 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15149543 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the left engine mount on Chevrolet S10? Posted by Customer
    A:
    The replacement procedure for the left Engine Mount begins with vehicle elevation along with shielding removal from under the body. Mobilize the through-bolt and nut from the Engine Mount located on the side under replacement. Raising the engine via a jack connected to the square tab on the left engine block rear (shown on left), you can access the square tab on its right side by possibly removing the Starter. Fuse enough power from the jack to remove the Engine Mount before extracting all the frame bracket bolts which allow you to take out the bracket. The procedure requires removing Engine Mount connecting bolts to engine before removing the mount assembly and associated shield. The installation process begins with sub-assembly of the Engine Mount and shield along with one bolt before their combined insertion into the engine compartment. Asset the procedure by first tightening the Engine Mount engine bolts to 55 nm (41 ft. Lbs.) and then installing the Engine Mount frame bracket onto the frame while tightening its bolts to 45 nm (33 ft. Lbs.). Set the engine at its dropped position then fit all Engine Mount through-bolts and nuts before torquing through-bolts to 74 nm (55 ft. Lbs.) and nuts to 63 nm (46 ft. Lbs.). Replace the Starter component if it was already taken out before ending the work by lowering the car.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the right engine mount on GMC Sonoma? Posted by Customer
    A:
    The first step to change the right Engine Mount calls for vehicle lift and shield removal from beneath. Start by removing the through-bolt and nut from the Engine Mount of the target side and place a jack on the engine block's rear square tab to lift the engine sufficiently to remove the Starter if needed for access to the right side square tab. Raising the engine slightly until you can remove the Engine Mount and then unfasten brackets that connect the mount to the frame and finally remove all brackets. The procedure begins with removing bolts that secure the Engine Mount to both the engine and vice-versa. You can then remove the Engine Mount together with its shield. You should start by sub-assembly of the Engine Mount and shield with one bolt before mounting them to the engine. Tighten the Engine Mount engine bolts to 54 nm (40 ft. Lbs.). Install the Engine Mount frame bracket onto the frame before securing it with bolts and referencing an 45 nm torque value (33 ft.lb.). Lower the engine from the jack support and fasten the Engine Mount through-bolts then nuts at 74 nm (55 ft. Lbs.) and 63 nm (46 ft. Lbs.) levels respectively. Reinstall the Starter only when it was taken out during the process and lower the vehicle back down.
    Posted by ChevyPartsGiant Specialist
    Q:
    What must be removed first when accessing the right side for the 2002 Chevrolet S10? Posted by Customer
    A:
    The starter must be removed first.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Engine Mount
    Q:
    What should be done after positioning the new mount for the 2002 Chevrolet S10? Posted by Customer
    A:
    Install the bolts that secure it to the transmission (2WD) or transfer case adapter (4WD).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after installing the transmission mount for the 2003 Chevrolet S10? Posted by Customer
    A:
    Lower the transmission and secure the transmission mount to the transmission support retaining nut, tightening it to 57 Nm (42 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the first step to replace the NV 3500 transmission mount for the 2003 GMC Sonoma? Posted by Customer
    A:
    Raise and support the vehicle, then support the transmission with a transmission jack.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    Q:
    What is the next step after relieving the weight on the mount for the 2003 GMC Sonoma? Posted by Customer
    A:
    Remove the transmission mount to the transmission or transfer case adapter mounting bolts and raise the transmission just enough to take out the transmission mount from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Motor And Transmission Mount
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Front Mount, Driver Side 15149543 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15149543 Front Mount, Driver Side is available in the market under the name GM Engine Mount, Motor And Transmission Mount. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15149543 Front Mount, Driver Side fits certain Chevrolet S10 models, as well as GMC Sonoma models.
The original GM component designated by manufacturer part number 15149543 maintains top performance when functioning as the Mount Assembly-Engine; Engine Mount Bracket; Motor Mount unit at its Driver Side. The component 15149543 is constructed from durable material and its dimensions span 7.4 x 6.2 x 6.2 inches while weighing 3.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting. The part 15149543 has available replacement options 15967993. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.