GM 10371429
Rear Driver Speaker, Passenger Side

The first step to replace the rear door speaker requires door trim panel detachment. First, remove screws which hold the speaker to the mounting bracket followed by disconnecting the electrical connector. Begin by removing the speaker from its bracket and then move to unfasten the speaker mounting bracket from the door with all necessary bolts. Start by inserting the speaker mounting bracket correctly on its position and fasten it to the door using bolts which require tightening at 6 N.m (53 lb in). After securing the speaker to the mounting bracket you must restore power through the electrical connector before fastening it with screws to 2 N.m (53 lb-in torque. Reinstall the door trim panel before checking the function of all components.

The first step to swap a rear door speaker includes the removal of door trim panels. First detach the screws maintaining the speaker to its mounting bracket and disconnect the electrical connector from the speaker. Disassemble the mounting bracket from the speaker and also free up the speaker mounting bracket bolts on your door when preparing to remove both pieces. Start installation with speaker mounting bracket placement followed by securement of bolts to the door while tightening them to 6 N.m (53 lb in). Connect the electrical connector to the speaker while the speaker mounts to its bracket. Install the speaker by screwing it to place using both screws which must be tightly fastened at 2 N.m (53 lb in). Reattach the door trim panel to complete the installation. Operation testing of the installed component must always follow completion of installation.

A Crew Cab owner should start the speaker installation by taking off the door trim panel. The first step involves removing two screws which secure the speaker onto its bracket then disconnecting its electrical connector. First disconnect the speaker from its mounting bracket. Depending on necessity you should first uninstall the bolts that secure the speaker bracket to the door prior to removing the bracket. Begin by setting the speaker mounting bracket into position then install the existing bolts that connect it to the door while tightening them to 6 N.m (53 lb in). Start by attaching the speaker on the mounting bracket before reconnecting the electrical connector then fasten the speaker with screws which you need to tighten to 2 N.m (53 lb in). After the operation check the component properly replace the door trim panel.

The first task for replacement of a rear door speaker involves taking away the door trim panel. Begin by uninstalling the screws which maintain the speaker to its mounting bracket before disconnecting the electrical connector attached to the speaker. The speaker must first be detached from its mounting bracket then you can proceed with removing the mounting bracket bolts from the door if required for complete bracket removal. Begin by positioning the speaker mounting bracket as it should be and secure it into the door with the specified bolts then tighten them to 6 N.m (53 lb in). First install the speaker onto the mounting bracket before reconnecting the electrical connector. Attach and tighten two screws on the speaker so they achieve a torque of 2 N.m (53 lb in), followed by replacing the door trim panel. A comprehensive check of component functionality must occur after finishing the installation step.

Move the console further back to access the subwoofer speaker, then remove the 4 retaining bolts and disconnect the wire connector.

Install the 4 retaining screws, ensuring they follow the same thread in the screw boss to avoid forming a new thread, and tighten them to 6 N.m (53 lb in).

Remove the speaker from the mounting bracket and, if necessary, take out the bolts that hold the speaker mounting bracket to the door before removing the bracket itself.

Install the 4 retaining screws, making sure they follow the same thread in the screw boss to avoid forming a new thread, and tighten them to 6 N.m (53 lb in).

Disconnect the electrical connector.

Install the trim panel and then inspect the component's operation.

Push down on the retainer to remove the speaker and disconnect the electrical connector.

Slightly move the center console rearward to disconnect the wire connector.

Remove the speaker from the mounting bracket and, if necessary, take out the bolts that hold the speaker mounting bracket to the door before removing the bracket itself.

First, remove the garnish molding.

Press the speaker back in until it is fully seated.

Take out the speaker and disconnect the electrical connectors as necessary.

Remove the windshield garnish molding.

Install the speaker by snapping it into place to ensure it is fully seated.

Verify the component's operation.

Move the console further back to access the subwoofer speaker and remove the 4 retaining bolts (W705202S).

Push down on the top retainer to remove the speaker, and disconnect the electrical connector.

Reconnect the electrical connector.

First, remove the trim panel.

Begin by removing the door trim panel.

Push the speaker into place, ensuring it is completely seated.