GM 12635954
Pressure Switch

After starting the process, kick off the battery's negative cable. Then, lift and prop up the vehicle in a proper place. Next, unscrew the electrical connector from engine oil pressure sensor and remove engine Oil Pressure Switch. In installation, make sure that you adhere to the fastener notice in service precautions and then fit the engine Oil Pressure Switch and tighten it to 16 nm (12 ft. Lbs.). Then rejoin the electrical connector to the engine Oil Pressure Switch, lower the vehicle, and lastly reconnect the battery bad cable.

Service of the Oil Pressure Switch requires first disconnecting the battery ground cable. Before switch removal it is critical to elevate and stabilize the vehicle while disconnecting the electrical connector from the engine Oil Pressure Switch. Installation requires adherence to fastener notice in service precautions with the engine Oil Pressure Switch and requires torque at 16 nm (12 ft. Lbs.). Reconnecting the electrical connector to the engine Oil Pressure Switch followed by vehicle lowering and battery ground (negative) cable connection.

In order to replace the engine oil pressure sensor or switch, start by disconnecting the battery negative cable. Second, unplug the electrical connector from the engine oil pressure sensor and then pull out the engine Oil Pressure Switch. For installation, make sure to refer to the fastener notice and install the engine Oil Pressure Switch after tighten it to 16 nm (12 ft. Lbs.). Then reconnect the electrical connector to the engine Oil Pressure Switch and finally, connect the battery negative cable.

The tool that you need to use for this procedure is the Oil Pressure Switch Socket (J 35749). To perform servicing of the oil pressure sensor, first, get the required tool. Take out the resonator of the air cleaner out, and subsequently, take out the oil pressure electrical connector. Next, unplug the switch socket of engine oil pressure Sense (J 35749); remove the engine oil pressure sensor. For installation one should use the Oil Pressure Switch Socket (J 35749) to install the engine oil pressure sensor , reconnect the oil pressure electrical connector , and lastly install the air cleaner outlet resonator .

Users need to elevate and sustain the vehicle during engine oil pressure sensor and switch installation. First disconnect the wire from the oil pressure indicator switch electrical connector before removing the switch from the engine block. Follow the correct part number instructions to apply sealer to the oil pressure indicator switch threads. Tighten the installed oil pressure indicator switch to a torque of 16 Nm (12 lb ft). To complete the procedure reconnect the oil pressure indicator switch electrical connector then lower the vehicle.

To replace engine oil pressure sensor or switch raise and support the vehicle. Detach the electrical connector from the engine oil pressure switch and unplug the oil pressure switch. When installing, make sure to adhere to the fastener notice service precautions. She has also talked about a Nigerian accent. By the same token, four years ago, when the author went to attend a student function, as he was about to come into the hall, these same boys used to call him bantu. Instead they might have used words like kean or born in Nigeria. Lastly, reattach the electrical connector to the engine oil pressure switch back in the engine compartment and lower the vehicle.

Begin the Oil Pressure Switch servicing process by disconnecting the negative battery ground cable. Raise the vehicle before finding a proper support point. Start by unplugging the electrical connector from the engine Oil Pressure Switch followed by removing the engine Oil Pressure Switch. Installation requires following service precautions mentioned on the fastener notice while tightening the engine Oil Pressure Switch to 13 nm (115 inch lbs.). Follow these installation steps: start by installing the engine Oil Pressure Switch then connect its electrical connector before lowering the vehicle and lastly reconnect the battery negative cable.

Start a replacement of the engine oil pressure sensor or switch by discharging the battery negative terminal cable from the battery. First disconnect the electrical connector from the engine oil pressure sensor followed by removing the engine Oil Pressure Switch. Install the engine Oil Pressure Switch after following the fastener notice and apply torque to 16 nm (12 ft. Lbs.). The procedure ends with connecting the battery negative cable to the battery while the installation begins with reconnecting the electrical connector to the engine Oil Pressure Switch.

If you need to replace the engine oil pressure sensor or switch, you will first need to raise and support the vehicle. Pull off the engine oil pressure switch electrical connector and disconnect it and remove the oil pressure switch. For installation, make sure you adhere to the Fastener Notic, followed by its installation of the engine oil pressure switch, tightening it to 16Nm (12ft. lbs.). Finally, connect the electrical connector of engine oil pressure switch and lower the vehicle.

Jamming off the battery negative cable should be your first step for replacing the engine oil pressure sensor or switch. Next raise the vehicle before properly supporting it. The next step involves removing both the electrical connector from the engine oil pressure sensor and the engine Oil Pressure Switch itself. Before switching begins follow the service precautions provided on the fasteners then establish the engine Oil Pressure Switch followed by a torque setting of 16 nm (12 ft. Lbs.). First step is to lower the vehicle to ground level before you reconnect the electrical connector to the engine Oil Pressure Switch. Then you can install the battery negative cable to complete the procedure.

Disconnect the battery ground (negative) cable and raise the vehicle securely.

Reconnect the electrical connector to the engine oil pressure sensor.

Check and fill the crankcase as necessary.

Connect the engine harness electrical connector to the oil pressure switch.

First, raise and support the vehicle.

Reconnect the electrical connector to the engine oil pressure switch.

Connect the electrical connector to the engine oil pressure sensor and lower the vehicle.

Raise and suitably support the vehicle.

Remove the air cleaner outlet resonator.

Use the Oil Pressure Switch Socket (J 35749) to remove the engine oil pressure sensor.

Raise and support the vehicle.

Connect the oil pressure indicator switch electrical connector and lower the vehicle.

Raise and support the vehicle.

Disconnect the engine oil pressure sensor electrical connector and remove the engine oil pressure sensor.

Connect the engine oil pressure switch electrical connector and lower the vehicle.

Disconnect the engine oil pressure sensor electrical connector and remove the engine oil pressure sensor.

Connect the engine oil pressure switch electrical connector and lower the vehicle.

Follow the fastener notice in service precautions.

Install the engine oil pressure switch and tighten it to 16 N.m (12 lb ft).

Connect the engine oil pressure switch electrical connector and lower the vehicle.

Detach the electrical connector from the engine oil pressure sensor and remove the engine oil pressure switch.

Tighten the new engine oil pressure switch to 16 N.m (12 lb ft) and reconnect the electrical connector.

Connect the battery negative cable.

Detach the electrical connector from the engine oil pressure sensor and remove the engine oil pressure switch.