How to replace the liftgate emblem and nameplate on 2008 Cadillac SRX?

To change the liftgate emblem and nameplate you need these tools: Heat Gun (J 25070). Heat Gun (J 25070). Protection tape should cover the emblem/nameplate during the initial setup process to maintain correct position. Heat the emblem/nameplate using the Heat Gun (J 25070) in circular patterns for about 30 seconds while maintaining the gun at a distance of 152 mm (6 in) from the surface. A small plastic flat-bladed tool takes off the emblem/nameplate in a way that preserves paint quality. The removal of adhesive requires a 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) for body panels or a lint-free cloth with Varnish Makers and Painters (VMP) naphtha and a 50/50 isopropyl alcohol and water mixture for plastic panels. A person must first ensure the installation surface is dry and clean before marking the previously unmarked location for SRX emblem placement. They should measure 130 mm (5.12 in) from the liftgate's horizontal edge while the vertical placement starts at 80 mm (3.12 in) and includes 12 mm (0.5 in) extra for export units. Use the Heat Gun (J 25070) to bring the mounting surface temperature to 27-41°C (80-105°F) while keeping the emblem/nameplate at 29-32°C (85-90°F). To place the emblem/nameplate following the marks, carefully remove the protective strip from the adhesive backing without touching it and firmly press the emblem/nameplate onto the surface. To achieve a uniform bond use equal pressure and check for proper adhesion then finish by manually rolling any loose parts before taking off the mounting surface tape.

OEM 2008 Cadillac SRX Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Emblems found

View related parts
2008 Cadillac SRX Center Cap, Black Part Number: 9596629
$47.99 MSRP: $68.66
You Save: $20.67 (31%)
ADD TO CART
Product Specifications
- Other Name: Cap-Hub Polished 19" Wheels *Black Backgr; Wheel Center Cap; Hub Cap; Emblem; Emblem, Wheel Cover Appearance; Cap, Wheel - Front And Rear; Cap, Wheel Trim
- Item Weight: 0.40 Pounds
- Item Dimensions: 6.8 x 4.7 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9596629
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Emblem Part Number: 84689784
$11.42 MSRP: $17.00
You Save: $5.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Side Door; Decal; Nameplate; Emblem, Cab, Load Carrier, Rear End, Door, Quarter Panel, Fender, Rocker Panel, Side Step.
- Replaces: 15223483, 15223484
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84689784
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Emblem, Rear Part Number: 25761282
$36.50 MSRP: $52.23
You Save: $15.73 (31%)
ADD TO CART
Product Specifications
- Other Name: Emblem, End Gate And Rear Door Decoration; Emblem,Rear End Panel And Tailgate
- Position: Rear
- Item Weight: 0.30 Pounds
- Item Dimensions: 3.7 x 3.7 x 0.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25761282
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Emblem, Front Part Number: 25765149
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Replaces: 25739143
- Item Weight: 0.40 Pounds
- Item Dimensions: 3.3 x 3.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25765149
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Emblem, Rear Part Number: 25761283
Product Specifications
- Other Name: Emblem, End Gate And Rear Door Decoration; Emblem,Rear End Panel And Tailgate
- Position: Rear
- Item Weight: 0.30 Pounds
- Item Dimensions: 3.7 x 3.0 x 0.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25761283
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Emblem, Front Part Number: 25765150
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Replaces: 25739188
- Item Weight: 0.40 Pounds
- Item Dimensions: 5.1 x 4.8 x 0.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25765150
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Nameplate, Rear Part Number: 10387855
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Emblem, End Gate And Rear Door Decoration; Emblem,Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Position: Rear
- Replaces: 10372469, 25739124, 25762472
- Item Weight: 0.30 Pounds
- Item Dimensions: 4.9 x 1.6 x 0.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10387855
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View related parts
2008 Cadillac SRX Nameplate, Rear Part Number: 10334040
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Position: Rear
- Item Weight: 0.30 Pounds
- Item Dimensions: 5.3 x 1.3 x 0.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10334040
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Cadillac SRX Submodels:
- Base | 8 Cyl 4.6 L GAS

2008 Cadillac SRX Emblem

With a comprehensive array of OEM 2008 Cadillac SRX Emblem, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Cadillac SRX Emblem are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Cadillac SRX Emblem Parts and Q&A

Q: How to replace the liftgate emblem and nameplate on 2008 Cadillac SRX?
A: To change the liftgate emblem and nameplate you need these tools: Heat Gun (J 25070). Heat Gun (J 25070). Protection tape should cover the emblem/nameplate during the initial setup process to maintain correct position. Heat the emblem/nameplate using the Heat Gun (J 25070) in circular patterns for about 30 seconds while maintaining the gun at a distance of 152 mm (6 in) from the surface. A small plastic flat-bladed tool takes off the emblem/nameplate in a way that preserves paint quality. The removal of adhesive requires a 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) for body panels or a lint-free cloth with Varnish Makers and Painters (VMP) naphtha and a 50/50 isopropyl alcohol and water mixture for plastic panels. A person must first ensure the installation surface is dry and clean before marking the previously unmarked location for SRX emblem placement. They should measure 130 mm (5.12 in) from the liftgate's horizontal edge while the vertical placement starts at 80 mm (3.12 in) and includes 12 mm (0.5 in) extra for export units. Use the Heat Gun (J 25070) to bring the mounting surface temperature to 27-41°C (80-105°F) while keeping the emblem/nameplate at 29-32°C (85-90°F). To place the emblem/nameplate following the marks, carefully remove the protective strip from the adhesive backing without touching it and firmly press the emblem/nameplate onto the surface. To achieve a uniform bond use equal pressure and check for proper adhesion then finish by manually rolling any loose parts before taking off the mounting surface tape.