Century | 1986-2005 | Custom, Estate Wagon, Limited, Special, Special Edition, T-Type | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS
Electra | 1986-1987 | Limited, Park Avenue, T-Type | 6 Cyl 3.8 L GAS
LaCrosse | 2005-2009 | CX, CXL | 6 Cyl 3.8 L GAS
LeSabre | 1992-2005 | Custom, Limited | 6 Cyl 3.8 L GAS
Lucerne | 2006-2008 | CX, CXL | 6 Cyl 3.8 L GAS
Park Avenue | 1992-2005 | Base, Ultra | 6 Cyl 3.8 L GAS
Regal | 1988-2004 | Custom, Gran Sport, GS, Limited, LS, LSE, Olympic Gold Edition | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
Rendezvous | 2002-2005 | CX, CX Plus, CXL, CXL Plus | 6 Cyl 3.4 L GAS
Riviera | 1995-1997, 1991-1993, 1986-1987 | Base, Luxury, T-Type | 6 Cyl 3.8 L GAS
Skyhawk | 1987-1989 | Custom, Limited, SE, Sport, T-Type | 4 Cyl 2.0 L GAS
Q: How to replace the ignition coil for Bank 2 on Buick LaCrosse?
A: The Ignition Coil replacement for bank 2 commences after turning off ignition and removing an engine cover to check parts without severing fuel pipes or hoses. Before changing the Ignition Coil for cylinder 2 you must disconnect the air cleaner duct from the Throttle Body as well as the positive crankcase ventilation (PCV) hose from the right bank camshaft cover but maintain the upper and lower intake manifolds in position. After removing the Intake Manifold bolts with bracing bolts (1 and 2) and the brace, reposition the upper Intake Manifold with the lower Intake Manifold to gain access for removing the ignition coils. First remove the Ignition Coil electrical connectors before taking out Ignition Coil bolts for Ignition Coil extraction. To install the coils put them back in their place according to the fastener notice and fasten the bolts to 10 n.m (89 lb in) torque and reattach the electrical connectors.
Q: How to replace the ignition coil for Bank 2 on Buick Enclave?
A: Replacing the ignition coil for the Bank 2 requires, firstly, the removal of the fuel injector sight shield, first. Then, unplug the engine wiring harness electrical connector(s) from the ignition coil(s) and unscrew the ignition coil bolt(s) before removing it. For installation, start by reinstalling the ignition coil(s) to place, remembering to hold the Fastener Notice. Then, install ignition coil bolt(s) and tighten them to 10 N.m (89 lb in). Then reconnect the engine wiring harness electrical connector(s), to the ignition coil(s) and lastly, install the fuel injector sight shield.
Q: How to service the ignition coil on Buick Regal?
A: You should start servicing the Ignition Coil by flipping the ignition off while removing the Spark Plug Wires but keeping track of their placement. Once the two screws holding the coil to the Ignition Control Module are removed you may take out the coil. Secure the Ignition Control Module with the coil assembly by installing the two attaching screws to 4-5 n.m (40 lb in) torque setting. Complete the service by reconnecting all Spark Plug Wires.