How to replace the outer CV Joint and seal on the wheel drive shaft on Buick LeSabre?

To change the outer joint and seal of the wheel drive shaft collect the tools: Drive Axle Seal Clamp Pliers (J35910), Drive Axle Swage Ring Clamp (J41048), and Snap Ring Pliers (J8059). Take out the large seal retaining clamp to the CV joint taking the help of side cutter and discard, then do the same to the small seal retaining clamp to the halfshaft bar. Remove the outboard seal from the CV joint outboard race and slide it out from the CV joint in the bar. Clean the inner race of CV joint of grease into the Snap Ring Pliers (J8059), then pry the ears of race flushing to remove the CV joint assembly from the bar. Locate the seal and take it off from the bar and carefully tap with the brass drift/hammer on the cage of the CV joint to remove the chrome alloy balls. Position the CV joint cage & inner race, 90 degree to the outer race, and align the windows with the lands of the outer race . Downside the inner and outer race assemblies, CV joint cage and balls, and remove every trace of old grease and contaminants by cleaning with cleaning solvent, followed by drying of parts. To assemble, position the new swage ring onto the small end of the joint seal and slide both on to the halfshaft bar. Use Drive Axle Swage Ring Clamp (J41048) in vise and hold the assembly while there is no pinch points on the seal and tighten the bolts alternately until snug. Apply a light coating of grease from the service kit to the ball grooves of the inner and outer races and insert the inner race in to the cage while aligning properly. Pull the cage and the inner race into the outer race, followed by the chrome balls, pack the CV joint with grease and make sure chassis outboard seal is in proper shape. Lastly, bring the large diameter of the outboard seal over the CV joint outer race and make an attempt to crimp the seal retaining clamp using its respective plier (Drive Axle Seal Clamp Pliers, J35910), a breaker bar and a torque wrench to tighten to 176 Nm (130 ft. lbs.) making sure that the gap dimension on the clamp ear is reached to 2.60mm (0.102 inch).

OEM Buick LeSabre CV Joint

CV Joint Axle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

19 CV Joints found

View related parts
Buick LeSabre CV Joints, Front Part Number: 26073382
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Front Part Number: 26073381
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Front Driver Side Part Number: 26073376
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Driver Side
- Replaces: 26073378
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Front Passenger Side Part Number: 26073375
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Inner Joint, Front Passenger Side Part Number: 26065931
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Driver Side Part Number: 26063190
Product Specifications
- Other Name: Joint Kit; CV Joint; Inner CV Joint; Inner Joint; Joint Kit, Front Wheel Drive Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Housing Assembly, Front Driver Side Part Number: 26062354
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint; Inner Joint Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Housing Assembly, Driver Side Part Number: 26060117
Product Specifications
- Other Name: Joint Kit; CV Joint; Inner Joint
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Housing Assembly, Front Passenger Side Part Number: 26060116
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner Joint
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Front Part Number: 26044398
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; CV Joints; Outer Joint; Outer Joint Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Front Part Number: 26020956
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Shaft CV; Axle Shaft; CV Joint; CV Boot; Axle Boots; CV Joint Kit; Outer Joint; Front Wheel Drive Axle
- Position: Front
- Replaces: 26003249
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1988 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints Part Number: 26003249
Product Specifications
- Other Name: CV Joint
- Replaced by: 26020956
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1988 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Outer Part Number: 19148843
Product Specifications
- Other Name: Outer CV Joint; CV Joint; CV Joints; Outer Joint; Outer Joint Assembly
- Position: Outer
- Replaces: 26044408, 26075595
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Outer Part Number: 19122437
Product Specifications
- Other Name: Outer CV Joint; CV Joint; CV Joints; Outer Joint; Outer Joint Assembly
- Position: Outer
- Replaces: 26044410, 26045070
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Front Part Number: 26044412
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Joint Assembly; Tripod Housing; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre CV Joints, Front Part Number: 26044411
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; Inner CV Joint; Housing Assembly; Joint Assembly; Tripod Housing; Inner Joint; Inner Joint Assembly; Tripod
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Front Part Number: 26021717
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; CV Joints; Outer CV Joint; CV Joint Kit; Outer Joint; Outer Joint Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Front Part Number: 26020960
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; CV Joint; CV Joints; CV Joint Kit; Joint Assembly
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Buick LeSabre | Base, Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre C.V. Joint, Front Part Number: 26020952
Product Specifications
- Other Name: Joint Kit, Front Wheel Drive Axle; Axle Shaft; CV Joint; CV Boot; CV Joints; Shaft Assembly; CV Joint Kit; Joint Assembly; Outer Joint; Outer Boot; Outer Joint Assembly; Joint
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1989-1991 Buick LeSabre | Base, Custom, Limited | 6 Cyl 3.8 L GAS

Buick LeSabre CV Joint

Want to cut long-term maintenance and repair costs? Choose OEM CV Joint. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick LeSabre parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick LeSabre CV Joint includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Knowing that Buick LeSabre CV Joint is a part that defines the characteristics of company's vehicles, it can be concluded that Buick offers only high-quality parts with a focus on the performance and durability. Being intended and effective for the smooth transfer of energy from the transmission to the drive wheels the CV Joint is rather important for the front-wheel-drive cars as well as for the newest rear-wheel-drive cars with independent suspension systems. There are numerous types of Buick LeSabre CV Joints namely; Rzeppa, tripod, and double offset joints, all of them are capable of providing constant velocity and are designed depending on the operational angles. Surrounding these joints are flexible rubber boots which contain lubricants and these prevent any contaminants from getting into these joints while at the same time maintaining their functionality in the long run. Having a tendency to inspect these boots often as this will help to preserve the CV Joints for any Buick LeSabre vehicles. Affordability to suit different models of Buick LeSabre increases the vehicle's effectiveness and security thus making Buick LeSabre CV Joint to stand out in the market. The LeSabre was produced for many years from 1959, up to 2005 and one can attest that the car had durability and performance, as manifested in the lineage of its sophisticated engineered CV joints. Modern options such as EyeCue headlights and StabiliTrak make the car impressive and deserving the title of the car with unique design and successful engineering solutions of the Buick LeSabre model. In conclusion, making Buick more than a driving experience, the Buick LeSabre CV Joint proves that quality and reliability are two values that the car makers adhere to.

Buick LeSabre CV Joint Parts Questions & Experts Answers

CV Joints, Front Passenger Side
26073375
Q: How to replace the outer CV Joint and seal on the wheel drive shaft on Buick LeSabre?
A:
To change the outer joint and seal of the wheel drive shaft collect the tools: Drive Axle Seal Clamp Pliers (J35910), Drive Axle Swage Ring Clamp (J41048), and Snap Ring Pliers (J8059). Take out the large seal retaining clamp to the CV joint taking the help of side cutter and discard, then do the same to the small seal retaining clamp to the halfshaft bar. Remove the outboard seal from the CV joint outboard race and slide it out from the CV joint in the bar. Clean the inner race of CV joint of grease into the Snap Ring Pliers (J8059), then pry the ears of race flushing to remove the CV joint assembly from the bar. Locate the seal and take it off from the bar and carefully tap with the brass drift/hammer on the cage of the CV joint to remove the chrome alloy balls. Position the CV joint cage & inner race, 90 degree to the outer race, and align the windows with the lands of the outer race . Downside the inner and outer race assemblies, CV joint cage and balls, and remove every trace of old grease and contaminants by cleaning with cleaning solvent, followed by drying of parts. To assemble, position the new swage ring onto the small end of the joint seal and slide both on to the halfshaft bar. Use Drive Axle Swage Ring Clamp (J41048) in vise and hold the assembly while there is no pinch points on the seal and tighten the bolts alternately until snug. Apply a light coating of grease from the service kit to the ball grooves of the inner and outer races and insert the inner race in to the cage while aligning properly. Pull the cage and the inner race into the outer race, followed by the chrome balls, pack the CV joint with grease and make sure chassis outboard seal is in proper shape. Lastly, bring the large diameter of the outboard seal over the CV joint outer race and make an attempt to crimp the seal retaining clamp using its respective plier (Drive Axle Seal Clamp Pliers, J35910), a breaker bar and a torque wrench to tighten to 176 Nm (130 ft. lbs.) making sure that the gap dimension on the clamp ear is reached to 2.60mm (0.102 inch).