How to service and repair the wiper arm on Buick LeSabre?

Start by setting the wipers in the park position then disconnect the washer hose from the air inlet grille panel to begin servicing the Wiper Arm. First remove the Wiper Arm nut cover then take out the Wiper Arm nut. Use Wiper Arm puller (J 39822) to detach the Wiper Arm from pivot shaft then remove arm from shaft. Use a finger to flex the Wiper Blade retaining clip while slowly pulling the blade off the Wiper Arm hook through the Wiper Blade's opening. To install the Wiper Blade simply place the arm hook through its opening and slide it onto the blade retaining clip until it clicks into position. Start by setting the wipers to park to shield against damage during the procedure. Activate the wiper system followed by moving the wiper control switch to the off position. Clean the wiper transmission pivot shaft knurls with a wire brush before installing the Wiper Arm onto the pivot shaft, aligning the Wiper Blade with the locating marks on the windshield, or centering the blades at the specified distances: passenger and driver-side blades should be spaced at 112.1 millimeters (4.41 inches) and 79.6 millimeters (3.13 inches). Ket the Wiper Arm pivot shaft with its installed nut to achieve 32nm of torque (4lbft) before you apply the protective covering. Apply windshield washer solvent to the washer hose to make fitting it onto the air inlet grille panel easier before tapping it to the fitting and checking wiper and washer operation.

How to replace the wiper arm on Buick LeSabre?

Start by putting the wipers into park and taking off the washer hose from the air inlet grille panel before replacing the Wiper Arm. Take off the cover from the nut and then unscrew the Wiper Arm nut. Grab the Wiper Arm with the Wiper Arm puller j 39822 and take the arm off the pivot shaft. After that, softly push down on the clip on the Wiper Blade, and take off the blade from the Wiper Arm hook by sliding it out the opening in the blade. Put the arm hook into the hole in the Wiper Blade and keep sliding it towards the blade retaining clip until you hear a click. Activate the wipers and turn the Wiper Switch to the off position to put the wiper system in park. Put the Wiper Arm on the pivot shaft and line up the Wiper Blade with the marks on the windshield. If there are no marks, locate the center of the blades at the specified distances: if there are no marks visible, make sure the blades' centers are at 112.1 mm (4.41 in) for the passenger side and 79.6 mm (3.13 in) for the driver side. Wipe off any debris from the wiper transmission pivot shaft knurls using a wire brush, and then put the nut onto the Wiper Arm pivot shaft, turning it tight to 32 n.m (24 lb ft). Put the cover over the nut, and attach the washer hose to the fitting on the air inlet grille panel using a little windshield washer solvent for ease of connection. Run the wipers and washers one last time to make sure they are working correctly.

OEM Buick LeSabre Wiper Arm

Windshield Wiper Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Wiper Arms found

View related parts
Buick LeSabre Wiper Blade Refill Part Number: 12339129
$4.85 MSRP: $7.92
You Save: $3.07 (39%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wiper, Windshield Wiper Blade; Windshield Wiper Blade Refills; Wiper Insert; Blade Insert; Blade Assembly Insert; Insert; Wiper Blade
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Black, Driver Side Part Number: 25646217
$18.18 MSRP: $45.20
You Save: $27.02 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Arm Assembly-Windshield Wiper *Black; Arm, Windshield Wiper Arm
- Position: Driver Side
- Replaces: 22110956
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Black Part Number: 25646216
$24.17 MSRP: $55.32
You Save: $31.15 (57%)
ADD TO CART
Product Specifications
- Other Name: Arm Assembly-Windshield Wiper *Black; Wiper Blade; Blade; Arm, Windshield Wiper Arm
- Replaces: 22155294, 22093285, 25643025
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Insert Part Number: 12463075
$13.11
ADD TO CART
Product Specifications
- Other Name: Wiper, Windshield Wiper Blade; Insert
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Blade Refill Part Number: 22143943
Product Specifications
- Other Name: Wiper, Windshield Wiper Blade; Windshield Wiper Blade Refills; Wiper Blade Insert; Wiper Insert; Blade Insert; Blade Assembly Insert; Insert; Wiper, Windshield Wiper; Wiper Blade
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Passenger Side Part Number: 20634672
Product Specifications
- Other Name: Arm; Arm, Windshield Wiper Arm
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Driver Side Part Number: 10364941
$60.76 MSRP: $108.50
You Save: $47.74 (44%)
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Driver Side
- Replaces: 12463073, 12494815, 25704865
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Passenger Side Part Number: 10364940
$52.74 MSRP: $94.18
You Save: $41.44 (44%)
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Passenger Side
- Replaces: 12463072, 12494816, 25704864
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Driver Side Part Number: 25695425
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Driver Side
- Replaces: 25647727
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Passenger Side Part Number: 25695424
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Passenger Side
- Replaces: 25647726
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Driver Side Part Number: 20695024
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Driver Side
- Replaces: 20693403, 22093215
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Wiper Arm, Driver Side Part Number: 20004890
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Wiper Arm, Passenger Side Part Number: 20004889
Product Specifications
- Other Name: Arm, Windshield Wiper Arm
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL

Buick LeSabre Wiper Arm

Want to cut long-term maintenance and repair costs? Choose OEM Wiper Arm. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick LeSabre parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick LeSabre Wiper Arm includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Buick LeSabre Wiper Arm is a vital section that greatly contributes to the steadiness and efficiency of the car by providing adequate and clear wipe during wiping at appropriate times. This Wiper Arm is the part that links the wiper blades to the motor, or more specifically, it transfers the rotational pressure of the motor back and forth into the sweeping action that is instrumental in wiping of rain, snow and other forms of wetness off the windshield. Manufactured for the Buick LeSabre models that were produced between 1959 and 2005, Wiper Arm is used to uphold the safety and performance of the vehicle and is therefore essential. The Buick LeSabre, which has such characteristics as power, durability, and workaholic, has always served driver and passengers' safety and protection, where the Wiper Arm occupies a significant place. In the later models, it has the RainSense wipers, which in the Buick LeSabre Wiper Arm adapts to the wetness of the environment and in the process boosts visibility. This to strengthen a proposal of the adjustment of its life through the LeSabres progression over the years such as changes made to the aerodynamics have also affected the functionality of the Wiper Arm. This is due to the passion Buick has of providing the optimal that can be expected of an automobile and a living proof is the LeSabre Wiper Arm. Altogether, it is not just this part of the car; it is the Buick LeSabre Wiper Arm and symbolizes the drive that the Buick LeSabre brings to all drivers and assures them they can drive through storms and rain and be safe and secure behind the wheel.

Buick LeSabre Wiper Arm Parts and Q&A

Wiper Arm, Driver Side
10364941
Q: How to service and repair the wiper arm on Buick LeSabre?
A:
Start by setting the wipers in the park position then disconnect the washer hose from the air inlet grille panel to begin servicing the Wiper Arm. First remove the Wiper Arm nut cover then take out the Wiper Arm nut. Use Wiper Arm puller (J 39822) to detach the Wiper Arm from pivot shaft then remove arm from shaft. Use a finger to flex the Wiper Blade retaining clip while slowly pulling the blade off the Wiper Arm hook through the Wiper Blade's opening. To install the Wiper Blade simply place the arm hook through its opening and slide it onto the blade retaining clip until it clicks into position. Start by setting the wipers to park to shield against damage during the procedure. Activate the wiper system followed by moving the wiper control switch to the off position. Clean the wiper transmission pivot shaft knurls with a wire brush before installing the Wiper Arm onto the pivot shaft, aligning the Wiper Blade with the locating marks on the windshield, or centering the blades at the specified distances: passenger and driver-side blades should be spaced at 112.1 millimeters (4.41 inches) and 79.6 millimeters (3.13 inches). Ket the Wiper Arm pivot shaft with its installed nut to achieve 32nm of torque (4lbft) before you apply the protective covering. Apply windshield washer solvent to the washer hose to make fitting it onto the air inlet grille panel easier before tapping it to the fitting and checking wiper and washer operation.
Wiper Arm, Passenger Side
10364940
Q: How to replace the wiper arm on Buick LeSabre?
A:
Start by putting the wipers into park and taking off the washer hose from the air inlet grille panel before replacing the Wiper Arm. Take off the cover from the nut and then unscrew the Wiper Arm nut. Grab the Wiper Arm with the Wiper Arm puller j 39822 and take the arm off the pivot shaft. After that, softly push down on the clip on the Wiper Blade, and take off the blade from the Wiper Arm hook by sliding it out the opening in the blade. Put the arm hook into the hole in the Wiper Blade and keep sliding it towards the blade retaining clip until you hear a click. Activate the wipers and turn the Wiper Switch to the off position to put the wiper system in park. Put the Wiper Arm on the pivot shaft and line up the Wiper Blade with the marks on the windshield. If there are no marks, locate the center of the blades at the specified distances: if there are no marks visible, make sure the blades' centers are at 112.1 mm (4.41 in) for the passenger side and 79.6 mm (3.13 in) for the driver side. Wipe off any debris from the wiper transmission pivot shaft knurls using a wire brush, and then put the nut onto the Wiper Arm pivot shaft, turning it tight to 32 n.m (24 lb ft). Put the cover over the nut, and attach the washer hose to the fitting on the air inlet grille panel using a little windshield washer solvent for ease of connection. Run the wipers and washers one last time to make sure they are working correctly.