How to replace the upper intake manifold on Cadillac SRX?

Begin your upper Intake Manifold replacement process by shutting off the ignition and setting aside the fuel injector sight shield and air inlet duct alongside the Brake Booster Vacuum Hose. Separate the wiring harness retaining bracket from the Throttle Body electrical connection before you disconnect the Throttle Body connector and the purge solenoid valve connector from its electrical harness and purge line. Disassemble the upper Intake Manifold assembly completely by removing the brace stud , bolt , and brace followed by detaching the pcv hose from right bank camshaft cover, barometric pressure sensor electrical connector, and Intake Manifold runner control solenoid electrical connector. After you remove the injector harness bracket bolt and the left bank ignition coil wiring harness from the bracket you can remove the upper Intake Manifold bolts but sometimes you'll need to deflect the cowl panel to obtain the right rear bolt. Take out the upper Intake Manifold that includes the Throttle Body for replacement while you must disassemble and clean up and inspect any replaceable upper Intake Manifold. Construct an Intake Manifold for replacement if necessary then position a new upper Intake Manifold gasket before installing the upper Intake Manifold. Start by tightening the upper Intake Manifold bolts at the center and move toward the exterior until each bolt reaches 23 nm (17 ft. Lbs.). Connect the right bank camshaft cover to barometric pressure sensor electrical connector and Intake Manifold runner control solenoid electrical connector alongside pcv hose. After installing the upper Intake Manifold brace with its bolt and stud you must tighten both components. Start by bolting to 65 nm (48 ft. Lbs.) then stud to 10 nm (89 inch lbs.). Connect the electrical connector across the Throttle Body while making sure the wiring harness connector properly locks into place before putting on the retainer. The purge system requires a connection between the purge line and solenoid valve and its power source in addition to reestablishing the vacuum hose from the Intake Manifold to the brake booster. Then attach the air inlet duct and fuel injector shield.

OEM Cadillac SRX Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Intake Manifolds found

View related parts
Cadillac SRX Intake Manifold Part Number: 12699182
$333.95 MSRP: $573.52
You Save: $239.57 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Intake Plenum; Manifold
- Replaces: 12648915, 12635243
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2016 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Cadillac SRX Intake Plenum, Upper Part Number: 55561791
$197.61 MSRP: $456.11
You Save: $258.50 (57%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Upper Intake; Manifold, Engine Fuel Intake Manifold
- Position: Upper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2011 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 3.0 L GAS
View related parts
Cadillac SRX Intake Manifold Part Number: 19330172
$606.14 MSRP: $1031.91
You Save: $425.77 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold; Manifold, Engine Fuel Intake Manifold
- Replaces: 19303933, 12588847, 12564771
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Cadillac SRX | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac SRX Intake Manifold Part Number: 12611155
$348.50 MSRP: $574.12
You Save: $225.62 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Engine Intake Manifold
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2016 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Cadillac SRX Intake Manifold Part Number: 12634205
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2011 Cadillac SRX | Base, Luxury, Performance, Premium | 6 Cyl 3.0 L GAS
View related parts
Cadillac SRX Intake Manifold Part Number: 19371505
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Replaces: 12571079, 92068635
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Cadillac SRX | Base | 6 Cyl 3.6 L GAS
View related parts
Cadillac SRX Intake Plenum Part Number: 12597853
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Position: Upper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Cadillac SRX | Base | 6 Cyl 3.6 L GAS
View related parts
Cadillac SRX Intake Plenum Part Number: 12587556
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Position: Upper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 Cadillac SRX | Base | 6 Cyl 3.6 L GAS

Cadillac SRX Intake Manifold

Want to cut long-term maintenance and repair costs? Choose OEM Intake Manifold. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac SRX parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac SRX Intake Manifold includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

As one of the many parts of a Cadillac SRX, the Intake Manifold is an incredibly important part that greatly improves the Cadillac's mid-size luxury SUV capabilities and durability. As responsible for supplying air or air/fuel mixture to each cylinder in the most effective manner possible, the SRX Intake Manifold is an integral component that predetermines the engine's power-to-weight ratio and standard coefficient of efficiency. Cadillac has designed this feature the SRX Intake Manifold and uses contemporary materials: chiefly a lightweight plastic composite; effective at getting better fuel economy, and cool. The design also has variable length intake manifolds (VLIM) which changes depending with the loading of the engine; thus ensuring that there is the right amount of air movement within the engines depending on the driving condition. The SRX began in 2003 and up to the release of the second generation in 2016 the Intake Manifold is used, on this car the Intake Manifold fits the high feature V6 engine and the direct injection engines in the second generation Cadillac SRX. This reflects Cadillac's flexibility as the SRX Intake Manifold also enhances safety and fuel efficiency; acceleration, towing capacity and power. Luxurious interiors and safety technologies make this car a target to discriminating buyers in the automotive industry due to the combination of power and elegance represented by Cadillac SRX. The role of the Intake Manifold for reliability and performance seals the necessity of its existence to the total engineering of Cadillac cars and hence, has become part of what makes a Cadillac SRX go.

Cadillac SRX Intake Manifold Parts Questions & Experts Answers

Intake Manifold
19330172
Q: How to replace the upper intake manifold on Cadillac SRX?
A:
Begin your upper Intake Manifold replacement process by shutting off the ignition and setting aside the fuel injector sight shield and air inlet duct alongside the Brake Booster Vacuum Hose. Separate the wiring harness retaining bracket from the Throttle Body electrical connection before you disconnect the Throttle Body connector and the purge solenoid valve connector from its electrical harness and purge line. Disassemble the upper Intake Manifold assembly completely by removing the brace stud , bolt , and brace followed by detaching the pcv hose from right bank camshaft cover, barometric pressure sensor electrical connector, and Intake Manifold runner control solenoid electrical connector. After you remove the injector harness bracket bolt and the left bank ignition coil wiring harness from the bracket you can remove the upper Intake Manifold bolts but sometimes you'll need to deflect the cowl panel to obtain the right rear bolt. Take out the upper Intake Manifold that includes the Throttle Body for replacement while you must disassemble and clean up and inspect any replaceable upper Intake Manifold. Construct an Intake Manifold for replacement if necessary then position a new upper Intake Manifold gasket before installing the upper Intake Manifold. Start by tightening the upper Intake Manifold bolts at the center and move toward the exterior until each bolt reaches 23 nm (17 ft. Lbs.). Connect the right bank camshaft cover to barometric pressure sensor electrical connector and Intake Manifold runner control solenoid electrical connector alongside pcv hose. After installing the upper Intake Manifold brace with its bolt and stud you must tighten both components. Start by bolting to 65 nm (48 ft. Lbs.) then stud to 10 nm (89 inch lbs.). Connect the electrical connector across the Throttle Body while making sure the wiring harness connector properly locks into place before putting on the retainer. The purge system requires a connection between the purge line and solenoid valve and its power source in addition to reestablishing the vacuum hose from the Intake Manifold to the brake booster. Then attach the air inlet duct and fuel injector shield.