How to replace the front brake pads on Chevrolet Camaro?

The Brake Pad change process starts with draining two-thirds of the brake fluid from the master cylinder reservoir. After lifting the vehicle onto supports you should take out the tire and wheel assembly. Take the front brake caliper apart and extract its brake pads from the mounting plate through a screwdriver if needed. Test the caliper guide pins for easy movement before checking whether the guide pin boots sit correctly in place. Replace caliper guide pins when you notice severe damage and damage to their protective boots. Put the inner and outer pads into the brake caliper plate while being sure the wear sensor points to the trailing edge as the wheel turns forward. Put back the front brake caliper then tighten its pin bolts to 31 nm (23 ft. Lbs.). Press the brake pedal gently while running the engine until both inner and outer brake pads make contact with the rotor and create a steady pressure. Replace the tire and wheel parts then return the vehicle to normal height before replacing brake fluid with fresh fluid at proper fluid levels. Test the hydraulic brake system for leaks and finish the pads by slowly pressing the brake pedal when the engine runs.

How to replace the rear brake pads on Chevrolet Camaro?

The Brake Pad replacement process starts by draining two-thirds of the master cylinder's brake fluid amount before proceeding. First elevate and sustain the vehicle before taking off the tire alongside wheel. You need to install two wheel nuts to maintain the rotor's position. Position a c-clamp above the caliper housing and tighten it so the caliper piston moves to the bottom of the brake caliper while one end touches the brake hose fitting bolt/screw and the other end presses against the outer pad. Supportively remove the rear brake caliper from its mounting plate before properly handling it then remove both inner and outer brake pads from this plate. The shoe guide surfaces on the caliper mounting plate and rear brake caliper need cleaning before inspecting if the caliper guide pins move freely. Verify that the guide pin boot fits properly into its groove on the caliper. The guide pins and boots need replacement during maintenance if they become damaged or corroded. During pad installation position the inner pad containing the wear sensor close to the piston while ensuring that the sensor faces forward during wheel rotation. Select the other inner pad if this one cannot be installed. The pads need replacement when working on axle sets in vehicle brake systems. Fasten the mounting plate with the new inner and outer pads before you attach the rear brake caliper to its place on the plate. After removing wheel nuts from the rotor installation proceed by attaching the tire and wheel then lowering the vehicle. When the engine starts running press the brake pedal repeatedly until you achieve the desired Brake Pad to rotor contact for a firm brake feel. In the last step check the brake hydraulic system for leaks before you use the Brake Pad burnishing process.

OEM Chevrolet Camaro Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

32 Brake Pads found

View related parts
Chevrolet Camaro Brake Pads Part Number: 89047725
$149.86 MSRP: $411.92
You Save: $262.06 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaced by: 19433360
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010 Chevrolet Camaro | SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 92230273
$97.71 MSRP: $268.57
You Save: $170.86 (64%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 19421345
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | LS, LT | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Brake Pads, Front Part Number: 22907156
$212.95 MSRP: $413.31
You Save: $200.36 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 92244289
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Brake Pads, Front Part Number: 18026298
$49.57 MSRP: $136.27
You Save: $86.70 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Replaces: 18026165
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 Chevrolet Camaro | Base, Z28, Z28 SS | 6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Front Pads Part Number: 85115096
$405.40 MSRP: $727.18
You Save: $321.78 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Camaro | ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 86780718
$330.11 MSRP: $592.12
You Save: $262.01 (45%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaced by: 85642786
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chevrolet Camaro | ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Front Pads Part Number: 85115094
$285.36 MSRP: $511.86
You Save: $226.50 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Camaro | SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Camaro Brake Pads, Front Part Number: 19342236
$41.78 MSRP: $74.59
You Save: $32.81 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Assembly, Front Disc Brake
- Position: Front
- Replaces: 18028735
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1992 Chevrolet Camaro | Base, Berlinetta, Iroc-Z, LT, RS, RS Heritage Edition, Sport, Z28, Z28 Heritage Edition | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 23344220
$108.39 MSRP: $210.35
You Save: $101.96 (49%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2024 Chevrolet Camaro | LS, LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 92230269
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2015 Chevrolet Camaro | LS, LT | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 88899570
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 12454972
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2002 Chevrolet Camaro | Base, Z28, Z28 SS | 6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 22990625
$594.43 MSRP: $939.50
You Save: $345.07 (37%)
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Camaro | Z/28 | 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 22990624
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaced by: 23284028
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2015 Chevrolet Camaro | Z/28 | 8 Cyl 7.0 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 18028780
$39.98 MSRP: $71.40
You Save: $31.42 (45%)
Ships in 1-3 Business Days
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Replaces: 18028779
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Chevrolet Camaro | Berlinetta, Iroc-Z, LT, Sport, Z28 | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 18038575
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 Chevrolet Camaro | Base, Z28, Z28 SS | 6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads, Front Part Number: 18024917
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Chevrolet Camaro | Base, Indianapolis 500 Pace Car, Z28 | 6 Cyl 3.4 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 18020433
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1992 Chevrolet Camaro | Iroc-Z, RS, RS Heritage Edition, Z28, Z28 Heritage Edition | 6 Cyl 3.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 18021875
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Chevrolet Camaro | Base, Indianapolis 500 Pace Car, RS, Z28 | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads Part Number: 10132836
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1989 Chevrolet Camaro | Base, Iroc-Z, RS | 6 Cyl 2.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Chevrolet Camaro Brake Pads, Front Part Number: 12518935
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads; Pad Kit, Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1992 Chevrolet Camaro | Base, Iroc-Z, LT, RS, RS Heritage Edition, Sport, Z28, Z28 Heritage Edition | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS

| Page 1 of 2 |Next >

1-20 of 32 Results

Chevrolet Camaro Brake Pad

Want to cut long-term maintenance and repair costs? Choose OEM Brake Pad. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Camaro parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Camaro Brake Pad includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Camaro Brake Pad are parts of the braking system; pieces of metal that when forced against the spinning brake rotors, bring the car to a halt. These are pads that have been made of metals that can easily endured high temperatures that are noticeable to be approximately 400 degrees Fahrenheit. The brake pads have steel backing plates incorporated with friction material that willingly transfers to the rotor to produce the needed friction for an effective brake. Brake pad materials can also be classified into non-metallic, semi-metallic, fully-metallic and ceramics where each type has its own characteristic to suit a particular use. Maintenance and replacement of brake pads' are very important, wear indicators are used to remind when it is time to change set. Further, appropriate acquisition of the brake pads guarantees proper and efficient braking that may not cause problems such as brake fade or causing excessive rotor wear.

Chevrolet Camaro Brake Pad Parts and Q&A

Brake Pads, Front
18026298
Q: How to replace the front brake pads on Chevrolet Camaro?
A:
The Brake Pad change process starts with draining two-thirds of the brake fluid from the master cylinder reservoir. After lifting the vehicle onto supports you should take out the tire and wheel assembly. Take the front brake caliper apart and extract its brake pads from the mounting plate through a screwdriver if needed. Test the caliper guide pins for easy movement before checking whether the guide pin boots sit correctly in place. Replace caliper guide pins when you notice severe damage and damage to their protective boots. Put the inner and outer pads into the brake caliper plate while being sure the wear sensor points to the trailing edge as the wheel turns forward. Put back the front brake caliper then tighten its pin bolts to 31 nm (23 ft. Lbs.). Press the brake pedal gently while running the engine until both inner and outer brake pads make contact with the rotor and create a steady pressure. Replace the tire and wheel parts then return the vehicle to normal height before replacing brake fluid with fresh fluid at proper fluid levels. Test the hydraulic brake system for leaks and finish the pads by slowly pressing the brake pedal when the engine runs.
Brake Pads
88899570
Q: How to replace the rear brake pads on Chevrolet Camaro?
A:
The Brake Pad replacement process starts by draining two-thirds of the master cylinder's brake fluid amount before proceeding. First elevate and sustain the vehicle before taking off the tire alongside wheel. You need to install two wheel nuts to maintain the rotor's position. Position a c-clamp above the caliper housing and tighten it so the caliper piston moves to the bottom of the brake caliper while one end touches the brake hose fitting bolt/screw and the other end presses against the outer pad. Supportively remove the rear brake caliper from its mounting plate before properly handling it then remove both inner and outer brake pads from this plate. The shoe guide surfaces on the caliper mounting plate and rear brake caliper need cleaning before inspecting if the caliper guide pins move freely. Verify that the guide pin boot fits properly into its groove on the caliper. The guide pins and boots need replacement during maintenance if they become damaged or corroded. During pad installation position the inner pad containing the wear sensor close to the piston while ensuring that the sensor faces forward during wheel rotation. Select the other inner pad if this one cannot be installed. The pads need replacement when working on axle sets in vehicle brake systems. Fasten the mounting plate with the new inner and outer pads before you attach the rear brake caliper to its place on the plate. After removing wheel nuts from the rotor installation proceed by attaching the tire and wheel then lowering the vehicle. When the engine starts running press the brake pedal repeatedly until you achieve the desired Brake Pad to rotor contact for a firm brake feel. In the last step check the brake hydraulic system for leaks before you use the Brake Pad burnishing process.