How to replace the rear brake line on Chevrolet Lumina?

Securely elevate your vehicle before you proceed to replace the brake hose at the back. Clean all foreign material from brake hose and fittings after you take the wheel and tire off the rear. Apply a back up wrench to anchor the fitting while removing brake pipes from brake hose without letting pipes bend. Use tools to detach retainer clips keeping the brake hose in position at its brackets. Install the new brake hose into its brackets without bends so the hose fitting lines up perfectly with the bracket notch when following the hose paint stripe. Use a back up wrench to join the brake pipes to brake hose while holding the parts straight and fitting them down to 27 Nm torque. Install the tire and wheel back onto the car then bring it down. Perform the brake bleed technique and use the retainer clips to connect the hose fittings at the brackets.

How to replace the front brake line on Chevrolet Lumina?

Starting with replacement of a front brake hose requires securing the vehicle before any work begins. Clean away all dirt from the brake hoses and fittings after removing the front tire and wheel. A back up wrench should loosen the hose fitting while separating the brake pipe from the brake hose at the bracket while avoiding pipe or bracket deformation. Begin the installation by removing the bracket's retainer clip and hose and then proceeding to take out the brake hose bolt and hose and two washers which should be discarded. You must install the brake hose along with the brake hose bolt onto the caliper while placing the two new washers properly before lubricating the bolt threads with brake fluid to torque the bolt to 54 Nm (40 ft. lbs.). Secure the brake hose properly into its bracket slot by both avoiding bends and positioning the fitting to match the bracket's notch before stating the retainer clip. Use a back up wrench to connect the brake pipe to the brake hose while maintaining straight alignment of bracket and pipe before tightening the brake pipe tube nut to 15 Nm (11 ft. lbs.). Reinstall the front tire and wheel while making sure the brake hose stays away from suspension components during aggressive wheel movements. Adjustments to the hose length should be made whenever necessary. Lower the vehicle and perform the brake bleeding routine.

OEM Chevrolet Lumina Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Brake Lines found

View related parts
Chevrolet Lumina Flex Hose, Rear Part Number: 19173804
$10.28 MSRP: $18.35
You Save: $8.07 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 17999549, 18032567
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1994 Chevrolet Lumina | Base, Euro, Z34 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Rear Part Number: 22163167
$26.66 MSRP: $50.05
You Save: $23.39 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994 Chevrolet Lumina | Base, Euro, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Rear Driver Side Part Number: 19173568
$22.43 MSRP: $40.06
You Save: $17.63 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 17987367, 18032316
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Lumina | Base, Euro, Z34 | 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Rear Passenger Side Part Number: 19173567
$22.66 MSRP: $40.47
You Save: $17.81 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Replaces: 17987368, 18032315
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Lumina | Base, Euro, Z34 | 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Passenger Side Part Number: 10112054
$22.84 MSRP: $42.90
You Save: $20.06 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-2001 Chevrolet Lumina | Base, Euro, LS, LTZ, Z34 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Lumina Flex Hose, Passenger Side Part Number: 22163462
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaces: 22163458
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Lumina | Base, LS, LTZ | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Lumina Flex Hose, Driver Side Part Number: 22163461
Product Specifications
- Other Name: Brake Hose; Hydraulic Hose; Brake Line; Hose, Hydraulic Brake
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Chevrolet Lumina | Base, LS, LTZ | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Lumina Brake Hose, Driver Side Part Number: 22163457
Product Specifications
- Other Name: Hydraulic Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Lumina | Base, LS | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Rear Part Number: 19366759
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 17999820, 22163668, 22113390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Chevrolet Lumina | Base, Euro, Z34 | 4 Cyl 2.2 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Chevrolet Lumina Flex Hose, Driver Side Part Number: 10112053
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-2001 Chevrolet Lumina | Base, Euro, LS, LTZ, Z34 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Lumina Flex Hose Part Number: 22163367
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaces: 17999600
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 Chevrolet Lumina | Base, LS, LTZ | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

Chevrolet Lumina Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Lumina parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Lumina Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Brake Line is a necessary ingredient in the hydraulic braking system of Chevrolet Lumina automobiles facilitating transfer of brake fluid from master cylinder to the brake caliper pistons. This functionality is crucial in achieving fast Stopping/Slowing of the vehicle especially the Chevrolet Lumina thus improving the performance and safety of the vehicle. A brand that elicits trust, Brake Line has been manufactured with the strength to handle several types of driving terrains; aimed at cars made between the years 1989 and 2013. Supports many Lumina models, which surely pleases Chevrolet enthusiasts irrespective of the particular model of a car at hand. The Lumina's brake line system is typically a metal-based system; corrosion is a common issue during winter, and this often leads to fluid leaks and poor braking, therefore, requiring the use of high-quality stainless steel brake lines. This is a common problem in many Chevrolet Lumina cars and to solve it, many people try to upgrade better options for example in the form of braided stainless steel brake lines that enhances the car's brake pedal feel and sensitivity when driving at very high octaves. Furthermore, since ready made brake line kits are easily sourced and are made from corrosion materials, replacing the defective one in Chevrolet Lumina does not prove to be that hard thus retaining the reputation it manufacturers optimalowed to it. The market differentiation of the Brake Line is evident because apart from offering better braking performance the brake line also significantly contributes to safety of the driver and the passengers. Looking at the physical structure of the Brake Line, it is built to be strong enough but flexible when installed on almost all Lumina models that Chevrolet manufactures, this Brake Line continues to be an indispensable commodity for anyone who owns a Chevrolet Lumina.

Chevrolet Lumina Brake Line Parts and Q&A

Flex Hose, Driver Side
10112053
Q: How to replace the rear brake line on Chevrolet Lumina?
A:
Securely elevate your vehicle before you proceed to replace the brake hose at the back. Clean all foreign material from brake hose and fittings after you take the wheel and tire off the rear. Apply a back up wrench to anchor the fitting while removing brake pipes from brake hose without letting pipes bend. Use tools to detach retainer clips keeping the brake hose in position at its brackets. Install the new brake hose into its brackets without bends so the hose fitting lines up perfectly with the bracket notch when following the hose paint stripe. Use a back up wrench to join the brake pipes to brake hose while holding the parts straight and fitting them down to 27 Nm torque. Install the tire and wheel back onto the car then bring it down. Perform the brake bleed technique and use the retainer clips to connect the hose fittings at the brackets.
Flex Hose, Passenger Side
10112054
Q: How to replace the front brake line on Chevrolet Lumina?
A:
Starting with replacement of a front brake hose requires securing the vehicle before any work begins. Clean away all dirt from the brake hoses and fittings after removing the front tire and wheel. A back up wrench should loosen the hose fitting while separating the brake pipe from the brake hose at the bracket while avoiding pipe or bracket deformation. Begin the installation by removing the bracket's retainer clip and hose and then proceeding to take out the brake hose bolt and hose and two washers which should be discarded. You must install the brake hose along with the brake hose bolt onto the caliper while placing the two new washers properly before lubricating the bolt threads with brake fluid to torque the bolt to 54 Nm (40 ft. lbs.). Secure the brake hose properly into its bracket slot by both avoiding bends and positioning the fitting to match the bracket's notch before stating the retainer clip. Use a back up wrench to connect the brake pipe to the brake hose while maintaining straight alignment of bracket and pipe before tightening the brake pipe tube nut to 15 Nm (11 ft. lbs.). Reinstall the front tire and wheel while making sure the brake hose stays away from suspension components during aggressive wheel movements. Adjustments to the hose length should be made whenever necessary. Lower the vehicle and perform the brake bleeding routine.