Other Name: Knob Assembly-Manual Transmission Control Lever (W/O Shift Pattern) *Stone; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control
Fits the following Chevrolet Models:
Camaro | 2014-2015 | LS, LT, SS, Z/28, ZL1 | 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Red; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control; Knob, Transmission Control Lever
Fits the following Chevrolet Models:
Camaro | 2016-2020 | LS, LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Gray; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control; Knob, Transmission Control Lever
Replaces: 24276725, 24281292, 24284778
Fits the following Chevrolet Models:
Camaro | 2016-2024 | LS, LT | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Red; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Gray; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control; Knob, Transmission Control Lever
Other Name: Knob Assembly-Automatic Transmission Control Lever *Dark Atmospherr; Automatic Transmission Selector Handle; Knob, Transmission Control Lever
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Gray; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control
Other Name: Knob Assembly-Manual Transmission Control Lever (W/Boot & W/*Gray; Automatic Transmission Selector Handle; Knob, Transmission Gear Shift Control
Q: How to replace the shift knob on Chevrolet Equinox?
A: The procedure requires deploying the parking brake and rotating the key to the RUN position before attempting the replacement of the shift knob. Insert the lever of the shift knob into one of its low gear settings. Use a small flat bladed tool to lift the shift knob trim ring yet keep it 13.0mm (0.5 inch) below its original position to show the shift knob retaining screw. The shift knob screw requires you to turn it loosely by 4 to 5 turns before you pull out the shift knob from the shift control lever. To install this component place the shift knob onto the shift control lever before fastening the knob screw at 1.5 Nm (13 inch lbs.). You will hear a clicking sound when you lift the shift knob trim ring and successfully attach it to the shift knob. Check the shift knob button's proper operation in all available gears while keeping the shift control lever in PARK position and the key rotated to off.
Q: How to replace the floor shift knob on Chevrolet Malibu?
A: The replacement of the floor Shift Knob begins with releasing the boot from the Shift Knob through downward pull of the boot retainer. The first step involves disconnecting the Shift Knob retaining screw then pulling the Shift Knob off from its position on the shift control. The Shift Knob installation process requires fitting it against the shift control first while following safe fastener guidance. Next install the Shift Knob retaining screw with 4 nm force (35 lb in) before you replug the boot into the console.
Q: How to replace the Shift Knob on Chevrolet Traverse?
A: The first step for replacing the Shift Knob on the traverse involves engaging the parking brake while removing the floor console left extension panel. Before disconnecting the transmission tap up/tap down switch electrical connector it is crucial to note the wire harness position for accurate reinstallation. Pull out the tap up/tap down switch electrical wire harness from its retainments on the shift control device as well as the base. Lower the transmission shift control lever all the way to its rear position when the key is in the run mode (without engine start) before continuing. Downward pressure should be applied to the Shift Knob trim ring in order to disconnect it from the Shift Knob and reveal the Shift Knob retaining screw. Open the shift control knob screw and guide the transmission tap up/tap down switch electrical harness and connector through the shift control indicator during shift control knob removal. The procedure for installation requires guiding the electrical fixture through the shift control indicator twice before attaching the shift control knob to the shift control lever. Drive in and secure the control knob screw with a torque of 4 nm (35 lb in). Pulling the shift control knob trim ring will produce an audible click that indicates proper attachment. After placing the shift control lever in park position along with turning the key off the technician should reinstall the tap up/tap down switch electrical wire harness to its retaining features. Test the shift control through all gear ranges after connecting the transmission tap up/tap down switch electrical connector. The maintenance ends with installing left extension panel on the floor console then releasing the parking brake.