How to replace the rear disc brake pads on the 1500 Series on Chevrolet Tahoe?

To change the rear disc brake pads on the 1500 series, first, check the fluid level in a brake master cylinder reservoir. If above the midway point between the full in max and min allowable, drain to midway. Lift the vehicle and remove its tire and wheel assembly. Compress the Brake Caliper Piston through a strong c-clamp over the top of the caliper housing against the back of the outboard pad until the piston is fully retracted. Using hand tools, loosen the guide pin bolt and hold the guide pin with an open end wrench as you support the caliper with heavy mechanic wire to prevent damage from occurring to the hydraulic flexible brake hose. Unscrew the guide pin bolt from the brake caliper, then rotate the brake caliper up and rest it as needed. Take off the brake pads and retaining springs of the mounting bracket, making sure to replace the old springs with new ones. The next step involves installing the new retaining springs on the caliper mounting bracket and the new brake pads and removing the mechanic wire and rotating the brake caliper back to its position. Install new caliper guide pin bolts and tighten them to 38 nm (c28 lb ft) while maintaining the guide pin in an open end wrench. Put the tire and wheel assembly back on; lower the car; with the engine off, press down on the Brake Pedal gently to about 2/3 travel and let it off. Keep repeating until a firm pedal is obtained to effectively position the break caliper pistons and brake pads. Last but not least, top up the brake master cylinder reservoir to the correct level using clean brake fluid and burnish the brake pads and rotors.

How to replace the front disc brake pads on the 1500 Series on Chevrolet Tahoe?

Before installing new front disc brake pads on the 1500 series check the fluid level inside the brake master cylinder reservoir. The fluid level needs removal to the point halfway between maximum-full and minimum allowable limits. Start by lifting and securing the car before you remove the tire and wheel assembly. Tighten two large c-clamps placed over the caliper housing to pull in the pistons until they rest completely inside the caliper assembly. Loosen the lower brake caliper guide pin bolt with an open end wrench then remove the bolt while simultaneously using heavy mechanic wire to support the brake caliper to protect the hydraulic flexible brake hose. While propping up the caliper you should remove the mounting bracket's brake pads together with its spring clips. Wipe down the pad contact area of the caliper bracket with denatured alcohol while avoiding damage to the dust seals of the pistons. Brake Pad installation requires cleaning both Brake Caliper Piston faces and caliper housing from adhesive residue. Add a thin layer of high temperature silicone brake lubricant to the pad mating surfaces on the caliper bracket before putting in new spring clips when replacing brake pads or reinstalling the original clips when using existing pads. Align brake pads according to their original position before reinstalling the brake caliper onto its mounting bracket. An open end wrench should hold the caliper guide pin in place as you tighten the brake caliper guide pin bolt to 100 nm (74 lb ft). Place the tire assembly back on the vehicle and lower it down before slowly applying the brake pedal to around 2/3 of its range while you turn the engine off. The process should continue until pedal firmness is reached and brake master cylinder reservoir demands additional clean fluid for maintenance. Use a firm grip on the brake pedal for 30 seconds followed by another 30 seconds of pressure application to help the insulators of brake pads properly connect with the brake caliper pistons and caliper housing. After completing these steps you will burnish the brake pads as well as rotors.

OEM Chevrolet Tahoe Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Brake Pads found

View related parts
Chevrolet Tahoe Brake Pads Part Number: 84320501
$102.16 MSRP: $214.06
You Save: $111.90 (53%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 23135915, 84218390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 84176464
$86.00 MSRP: $178.61
You Save: $92.61 (52%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaced by: 85601646
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 25910432
$126.02 MSRP: $244.58
You Save: $118.56 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Tahoe Front Pads Part Number: 25910431
$95.20 MSRP: $274.50
You Save: $179.30 (66%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
- Replaced by: 84233332
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Chevrolet Tahoe | Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Chevrolet Tahoe Brake Pads Part Number: 84218394
$197.74 MSRP: $386.41
You Save: $188.67 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 23487649
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads, Red Caliper Part Number: 85524066
$113.81 MSRP: $220.90
You Save: $107.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Replaced by: 85663434
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Rear Pads Part Number: 86793555
$57.50 MSRP: $111.60
You Save: $54.10 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 85537461
$262.75 MSRP: $451.26
You Save: $188.51 (42%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Replaces: 84805876
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads, Red Caliper Part Number: 84987498
$263.17 MSRP: $510.76
You Save: $247.59 (49%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 84176465
$100.84 MSRP: $207.24
You Save: $106.40 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaced by: 85644145
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads, Front Part Number: 25852957
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 89059119
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chevrolet Tahoe | LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 22742382
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 25918342
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Tahoe Brake Pads Part Number: 19329677
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 15792633, 23112025, 25949454, 15945636
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 19210705
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads
- Position: Rear
- Replaces: 18041762, 18026217
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Brake Pads, Front Part Number: 18048101
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads; Pad Kit, Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 18045936
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Replaces: 18043517, 18044202
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Brake Pads Part Number: 88964192
$111.96 MSRP: $200.82
You Save: $88.86 (45%)
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS

Chevrolet Tahoe Brake Pad

Want to cut long-term maintenance and repair costs? Choose OEM Brake Pad. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Tahoe parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Tahoe Brake Pad includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Brake Pad used in Chevrolet Tahoe models are parts of the braking system that works by friction that eventually slows down the vehicle. These pads are normally made up of metallic and man-made materials; a feature which makes them quite heat resistant and operational at temperatures that may rise up to 400 degrees Fahrenheit in their normal course of use. The pads naturally wear out over time and require regular replacement and most model of Tahoe comes with wear sensors/indicator to inform the driver when the pads are worn out. Over the time, several forms of Brake Pad have been used in the Tahoe, such as the non metallic, the semi metallic, fully metallic and ceramic. Each type has its pros in the question of friction, wear resistance, as well as noise. Regular services, especially if dealing with associated hardware such as clips and springs, are therefore very central in a brake pad's performance and durability to provide safe and effective braking.

Chevrolet Tahoe Brake Pad Parts and Q&A

Brake Pads
22742382
Q: How to replace the rear disc brake pads on the 1500 Series on Chevrolet Tahoe?
A:
To change the rear disc brake pads on the 1500 series, first, check the fluid level in a brake master cylinder reservoir. If above the midway point between the full in max and min allowable, drain to midway. Lift the vehicle and remove its tire and wheel assembly. Compress the Brake Caliper Piston through a strong c-clamp over the top of the caliper housing against the back of the outboard pad until the piston is fully retracted. Using hand tools, loosen the guide pin bolt and hold the guide pin with an open end wrench as you support the caliper with heavy mechanic wire to prevent damage from occurring to the hydraulic flexible brake hose. Unscrew the guide pin bolt from the brake caliper, then rotate the brake caliper up and rest it as needed. Take off the brake pads and retaining springs of the mounting bracket, making sure to replace the old springs with new ones. The next step involves installing the new retaining springs on the caliper mounting bracket and the new brake pads and removing the mechanic wire and rotating the brake caliper back to its position. Install new caliper guide pin bolts and tighten them to 38 nm (c28 lb ft) while maintaining the guide pin in an open end wrench. Put the tire and wheel assembly back on; lower the car; with the engine off, press down on the Brake Pedal gently to about 2/3 travel and let it off. Keep repeating until a firm pedal is obtained to effectively position the break caliper pistons and brake pads. Last but not least, top up the brake master cylinder reservoir to the correct level using clean brake fluid and burnish the brake pads and rotors.
Brake Pads
25910432
Q: How to replace the front disc brake pads on the 1500 Series on Chevrolet Tahoe?
A:
Before installing new front disc brake pads on the 1500 series check the fluid level inside the brake master cylinder reservoir. The fluid level needs removal to the point halfway between maximum-full and minimum allowable limits. Start by lifting and securing the car before you remove the tire and wheel assembly. Tighten two large c-clamps placed over the caliper housing to pull in the pistons until they rest completely inside the caliper assembly. Loosen the lower brake caliper guide pin bolt with an open end wrench then remove the bolt while simultaneously using heavy mechanic wire to support the brake caliper to protect the hydraulic flexible brake hose. While propping up the caliper you should remove the mounting bracket's brake pads together with its spring clips. Wipe down the pad contact area of the caliper bracket with denatured alcohol while avoiding damage to the dust seals of the pistons. Brake Pad installation requires cleaning both Brake Caliper Piston faces and caliper housing from adhesive residue. Add a thin layer of high temperature silicone brake lubricant to the pad mating surfaces on the caliper bracket before putting in new spring clips when replacing brake pads or reinstalling the original clips when using existing pads. Align brake pads according to their original position before reinstalling the brake caliper onto its mounting bracket. An open end wrench should hold the caliper guide pin in place as you tighten the brake caliper guide pin bolt to 100 nm (74 lb ft). Place the tire assembly back on the vehicle and lower it down before slowly applying the brake pedal to around 2/3 of its range while you turn the engine off. The process should continue until pedal firmness is reached and brake master cylinder reservoir demands additional clean fluid for maintenance. Use a firm grip on the brake pedal for 30 seconds followed by another 30 seconds of pressure application to help the insulators of brake pads properly connect with the brake caliper pistons and caliper housing. After completing these steps you will burnish the brake pads as well as rotors.