How to replace the intake manifold on GMC Canyon?

Initially remove all components including Throttle Body then disconnect battery box along with oil level indicator and tube as well as remove Brake Booster hose from Brake Booster and detach MAP Sensor electrical connector and MAP Sensor wiring harness retainer from the Intake Manifold. You need to detach the pcv dirty air tube from the camshaft cover followed by removing the generator and disconnecting the engine wiring harness retainer from the Intake Manifold . Elevate and hold the vehicle at a necessary height to reach components through the wheelhouse. Then remove the upper bolts securing the engine wiring harness bracket to the Intake Manifold. Disassemble the left front wheel together with its wheelhouse liner before you disconnect the Battery Cable, engine (4, 6), and MAP Sensor wiring harness retainers from the engine wiring harness bracket. After removing the last bolt from the engine wiring harness bracket proceed by pulling it out through the wheelhouse opening. Begin by removing the Intake Manifold bolts before lowering the vehicle to separate the Intake Manifold from the cylinder head. Remove the old seal before applying masking tape to cover the open ports of the cylinder head to stop foreign materials from entering the engine. First cleanse the Intake Manifold then install a new seal into the Intake Manifold groove and put the Intake Manifold into position on the cylinder head. Next raise and support the vehicle until you can reach the manifold bolts and engine harness bracket bolts and wiring harnesses. Install the Intake Manifold bolts, tightening them from the inside out to 10 nm (89 inch lbs.)after installing the bracket to the harnesses and engine follow steps by securing the bolts to 10 nm (89 inch lbs.). Fasten the Battery Cable and engine (4, 6) and MAP Sensor wiring harness retainers to the engine wiring harness bracket prior to reinstalling the left front wheelhouse liner and left front wheel when the vehicle is lowered. Connect engine wiring harness retainer through the Intake Manifold before generator installation and pcv dirty air tube attachment at the camshaft cover. First, install the Brake Booster hose to its location followed by reattaching the MAP Sensor wiring harness retainer with electrical connector. Complete the installation by reconnecting the oil level indicator and tube and re-installing the battery box and Throttle Body.

OEM GMC Canyon Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Intake Manifolds found

View related parts
GMC Canyon Intake Manifold Part Number: 89017742
$356.61 MSRP: $607.12
You Save: $250.51 (42%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 5 Cyl 3.5 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12699182
$333.95 MSRP: $573.52
You Save: $239.57 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Intake Plenum; Manifold
- Replaces: 12648915, 12635243
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | Base, SLE, SLT | 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12620308
$216.35 MSRP: $351.12
You Save: $134.77 (39%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Manifold
- Replaces: 12597598
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2010 GMC Canyon | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12698870
$47.51 MSRP: $74.41
You Save: $26.90 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Replaces: 12694867
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12675740
$219.07 MSRP: $372.92
You Save: $153.85 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 GMC Canyon | All Terrain, AT4, Base, Denali, Elevation, Elevation Standard, SLE, SLT | 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12638038
$224.44 MSRP: $382.10
You Save: $157.66 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2011-2012 GMC Canyon | SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12631023
$269.56 MSRP: $444.06
You Save: $174.50 (40%)
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 GMC Canyon | Base, Elevation, Elevation Standard, SL, SLE, SLT | 4 Cyl 2.5 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12611155
$348.50 MSRP: $574.12
You Save: $225.62 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold; Engine Intake Manifold
- Position: Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2016 GMC Canyon | Base, SLE, SLT | 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 89060572
Product Specifications
- Other Name: Manifold, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 GMC Canyon | SLE, SLT, WT | 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 89060571
Product Specifications
- Other Name: Manifold Assembly, Intake (Service); Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 GMC Canyon | SL, SLE, SLT, WT | 4 Cyl 2.9 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 89017801
Product Specifications
- Other Name: Manifold Assembly, Intake (Service); Oil Pump; Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2006 GMC Canyon | SL, SLE, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS
View related parts
GMC Canyon Intake Manifold Part Number: 12640048
Product Specifications
- Other Name: Manifold, Engine Fuel Intake Manifold
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2016-2022 GMC Canyon | All Terrain, AT4, Denali, Elevation, SLE, SLT | 4 Cyl 2.8 L DIESEL

GMC Canyon Intake Manifold

Want to cut long-term maintenance and repair costs? Choose OEM Intake Manifold. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Canyon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Canyon Intake Manifold includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Intake Manifold of GMC Canyon cars is responsible for feeding the air or air/fuel mixture to each cylinder of the engine and, therefore, influences the general performance and power of the auto car to a great extent. This works through drawing air from the throttle body or carburetor depending on the engine in question, the design may differ from one engine model to the other. For instance, carbureted and TBI engines fuel mix inside a manifold, the multiport fuel-injected engines imply individual injectors, GDI systems introduce only air to the cylinders. Different generations of GMC Canyon also had intake manifold which has changed from conventional cast iron, to aluminum and now to composite plastic which are lighter and has the feature of heat dissipation. Variable-length intake manifolds (VLIM) are present in some models which regulates flow and improves performances according to the load rate of the engines. Such developments make it possible for the GMC Canyon Intake Manifold to appropriately enhance the corresponding engine performance and power of the vehicle despite different configurations.

GMC Canyon Intake Manifold Parts and Q&A

Intake Manifold
89017742
Q: How to replace the intake manifold on GMC Canyon?
A:
Initially remove all components including Throttle Body then disconnect battery box along with oil level indicator and tube as well as remove Brake Booster hose from Brake Booster and detach MAP Sensor electrical connector and MAP Sensor wiring harness retainer from the Intake Manifold. You need to detach the pcv dirty air tube from the camshaft cover followed by removing the generator and disconnecting the engine wiring harness retainer from the Intake Manifold . Elevate and hold the vehicle at a necessary height to reach components through the wheelhouse. Then remove the upper bolts securing the engine wiring harness bracket to the Intake Manifold. Disassemble the left front wheel together with its wheelhouse liner before you disconnect the Battery Cable, engine (4, 6), and MAP Sensor wiring harness retainers from the engine wiring harness bracket. After removing the last bolt from the engine wiring harness bracket proceed by pulling it out through the wheelhouse opening. Begin by removing the Intake Manifold bolts before lowering the vehicle to separate the Intake Manifold from the cylinder head. Remove the old seal before applying masking tape to cover the open ports of the cylinder head to stop foreign materials from entering the engine. First cleanse the Intake Manifold then install a new seal into the Intake Manifold groove and put the Intake Manifold into position on the cylinder head. Next raise and support the vehicle until you can reach the manifold bolts and engine harness bracket bolts and wiring harnesses. Install the Intake Manifold bolts, tightening them from the inside out to 10 nm (89 inch lbs.)after installing the bracket to the harnesses and engine follow steps by securing the bolts to 10 nm (89 inch lbs.). Fasten the Battery Cable and engine (4, 6) and MAP Sensor wiring harness retainers to the engine wiring harness bracket prior to reinstalling the left front wheelhouse liner and left front wheel when the vehicle is lowered. Connect engine wiring harness retainer through the Intake Manifold before generator installation and pcv dirty air tube attachment at the camshaft cover. First, install the Brake Booster hose to its location followed by reattaching the MAP Sensor wiring harness retainer with electrical connector. Complete the installation by reconnecting the oil level indicator and tube and re-installing the battery box and Throttle Body.