C1500 | 1994-1999 | Sierra GT, Sierra SL, Sierra SLE, Sierra SLT, Sierra Special | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
C1500 Suburban | 1994-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
C2500 | 1994-2000 | Sierra SL, Sierra SLE, Sierra SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
C2500 Suburban | 1994-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
C3500 | 1994-2000 | Sierra SL, Sierra SLE, Sierra SLT | 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K1500 | 1994-1999 | Sierra SL, Sierra SLE, Sierra SLS, Sierra SLT, Sierra Special | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
K1500 Suburban | 1994-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
K2500 | 1994-2000 | Sierra SL, Sierra SLE, Sierra SLT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K2500 Suburban | 1994-1999 | Base, SLE, SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
K3500 | 1994-2000 | Sierra SL, Sierra SLE, Sierra SLT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
Q: How to replace the air conditioning evaporator core on GMC Canyon?
A: The first step to replace the air conditioning evaporator core is to remove the HVAC module assembly. Through screw removal process the HVAC module assembly parts can be split apart. Then proceed to remove and reinstall the evaporator temperature sensor control module screw. The first step is to divide the HVAC module assembly into two parts (1, 4) while extracting the evaporator temperature sensor from its position on the evaporator. The second step involves removing the evaporator core which is located inside the HVAC module assembly. Implement proper oil addition to the new evaporator core during installation as per the refrigerant system capacity requirements. The evaporator core installation requires insertion into the assembly followed by attachment of the evaporator temperature sensor to the core. Seal the HVAC module assembly halves before placement. Rebuild the HVAC module assembly while keeping to the fastener notice and use screws to join half sections by tightening each screw to 1.9 N.m (17 lb in). Finish by screwing and tightening the evaporator temperature sensor control module to 1.9 N.m (17 lb in) while putting the assembly back into place.
Q: How to replace the evaporator core on GMC Sierra 1500?
A: The process for replacing an evaporator core starts with heater/vent module removal through screw extraction and module separation. The removal of the evaporator core begins by extracting it from its position inside the heater/vent module. Put refrigerant oil in the new evaporator core during its installation process. Fit the new evaporator core inside the heater/vent module followed by rebuilding the module structure and tighten its screws to 1.6 N.m (14 lb in). The reinstallation of the heater/vent module requires A/C system evacuation and recharging followed by testing its fittings using J 39400-A.
Q: How to replace the air conditioning evaporator core on GMC Yukon?
A: The first step to replace the air conditioning Evaporator core consists of hvac module removal. When using the provided heat stakes separate them from the hvac module by using a screwdriver along with a hammer. Detach all wires from the Blower Motor and both sensors in addition to the Blower Motor control module and carefully remove extra wires from their retaining systems. You should disassemble the hvac module assembly by removing its screws if they are present. You should remove the Evaporator cowl gasket from the Evaporator before separating the upper hvac module assembly from the lower hvac module assembly . The Evaporator core must be removed from the upper component parts hierarchy of the hvac module assembly. Placing new refrigerant oil into the Evaporator core becomes necessary before installing it. The installation process starts with fitting the Evaporator core inside the hvac module before reattaching the upper hvac module assembly to the lower hvac module assembly followed by Evaporator cowl gasket fitting on the Evaporator. Secure the hvac module assembly with screws which should be tightened to 2 nm (18 lb in). Install the hvac module assembly after completing all procedures.