How to replace the drive pinion bearings on a 10.5 inch axle on GMC Yukon XL 2500?

The tools required to replace drive pinion bearings on a 10.5 inch axle consist of j 22388 (Pinion Oil Seal Installer-Rear), j 22761 (Differential Side Bearing Installer), j 22912-01 (Split Plate Bearing Puller), j 24433 (Pinion Cone and Side Bearing Installer), j 37624 (Pinion Bearing Installer), j 8092 (Universal Driver Handle - 3/4 in - 10), j 8608 (Rear Pinion Bearing Installer), and j 8614-01 (Flange and Pulley Holding Tool). Workers should first elevate the vehicle before taking out the Differential unit followed by the pinion gear bearing retainer, pinion yoke, oil seal, and outer Pinion Bearing. Enso and collapsible spacer must be removed before the j 22912-01 and hydraulic press extract the inner Pinion Bearing. A hammer along with a brass drift should be used to eliminate both the outer and inner Pinion Bearing cups. The procedure for installing pinion gear pilot bearing requires the j 22761 tool followed by an installation sequence of the inner Pinion Bearing cup using j 37624 and j 8092 then the outer Pinion Bearing cup needs to be installed with j 8608 and j 8092. After installing the inner Pinion Bearing with j 24433 you should add a new collapsible spacer before lubricating the pinion bearings. Feed the outer Pinion Bearing into the retainer and mount a fresh pinion oil seal by using j 22388 before inserting the pinion into its bearing retainer. Warm the pinion yoke splines before applying sealant. Install the yoke afterward and correctly attach it to the pinion shaft by using a soft-faced hammer. Tighten the new pinion nut under j 8614-01 tool torque until the pinion end play reaches its maximum resistance. Place the original shim or a 0.41 mm (0.016 inch) alternative shim when you need to replace the missing j 8614-01. Install the pinion gear bearing retainer onto the axle housing before fastening its bolts to 88 nm (65 ft. Lbs.). The measurement of rotating torque for used pinion bearings should fall within 1.0 to 2.3 nm (10 to 20 inch lbs.) while new pinion bearings should measure between 1.7 to 3.4 nm (15 to 30 inch lbs.). You should use the j 8614-01 torque wrench to increase pinion nut tightening steps until reaching the required specification torque. Rotating the pinion several times following torque confirmation helps bear in a proper position but rechecking the torque might be necessary for adjustment. To complete the task you must restore the Differential assembly while adjusting the side bearing preload and selecting drive pinion shims and adjusting backlash before filling with lubricant and returning the vehicle to the ground.

OEM GMC Yukon XL 2500 Pinion Bearing

Transmission Pinion Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 Pinion Bearings found

View related parts
GMC Yukon XL 2500 Output Shaft Bearing
Part Number: 12334861
$31.10 MSRP: $51.22
You Save: $20.12 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Axle Bearing; Bearing, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Wheel Bearing
Part Number: 9436881
$76.25 MSRP: $145.36
You Save: $69.11 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential; Differential Pinion Bearing; Differential Bearing; Axle Bearings; Shaft; Inner; Side; Differential Gear; Front Wheel; Rear Wheel; Nut.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013, 2000-2006 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 9413427
$56.84 MSRP: $109.76
You Save: $52.92 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearings; Differential Drive, Steering Knuckle King, Pinion Shaft, Front Axle Bearings.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Side Bearings
Part Number: 88943839
$48.83 MSRP: $144.56
You Save: $95.73 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Replaces: 26091723
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings, Inner
Part Number: 457108
$55.00 MSRP: $154.36
You Save: $99.36 (65%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion Bearings.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 454021
$161.60 MSRP: $292.48
You Save: $130.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear; Differential Pinion Bearing; Rear Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion; Rear Wheel Bearing.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Seal, Outer
Part Number: 25824252
$50.72 MSRP: $95.24
You Save: $44.52 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Pinion Bearings; Side Bearings; Bearing; Bearing, Pinion Shaft Front
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings, Inner
Part Number: 25824251
$59.57 MSRP: $176.34
You Save: $116.77 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Side Bearings; Bearing, Drive Pinion Rear And Intermediate
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Side Bearings
Part Number: 25824250
$72.20 MSRP: $140.14
You Save: $67.94 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Replaces: 09418390, 9418390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 23243839
$71.22 MSRP: $139.44
You Save: $68.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Rear Pinion Bearing; Front/Inner/Outer Pinion; Diff/Drive Axle; Pinion/Clutch/Rear Wheel
- Position: Front
- Replaces: 09418357, 26053758, 9418357, 15286375, 20997052, 22786621, 9418356, 09418356, 12479221
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Side Bearings
Part Number: 11505123
$56.18 MSRP: $166.26
You Save: $110.08 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 9417781
$43.00 MSRP: $103.28
You Save: $60.28 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearing; Differential Drive Pinion Front, Drive Pinion, Pinion Shaft Front, Front Axle
- Position: Front Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 9414917
$70.11 MSRP: $133.08
You Save: $62.97 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Differential Bearing; Rear Pinion Bearing; Drive Pinion Rear; Axle Pinion Shaft; Ring And Pinion; Pinion Shaft Front.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013, 2003-2006 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings
Part Number: 9413168
$93.86 MSRP: $167.61
You Save: $73.75 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Roller; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Drive Pinion Bearing Assembly.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Pinion Bearings, Outer
Part Number: 15534483
$53.12 MSRP: $94.85
You Save: $41.73 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Front Pinion Bearing; Bearing, Differential Pinion; Bearing, Pinion Shaft Front
- Position: Outer
- Replaces: 09440836, 9440836
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS

GMC Yukon XL 2500 Pinion Bearing

Our website offers an extensive catalog of genuine GMC Yukon XL 2500 Pinion Bearing at unbeatable prices. Every OEM GMC Yukon XL 2500 Pinion Bearing comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

GMC Yukon XL 2500 Pinion Bearing Parts Questions & Experts Answers

Pinion Bearings, Inner
457108
Q: How to replace the drive pinion bearings on a 10.5 inch axle on GMC Yukon XL 2500?
A: The tools required to replace drive pinion bearings on a 10.5 inch axle consist of j 22388 (Pinion Oil Seal Installer-Rear), j 22761 (Differential Side Bearing Installer), j 22912-01 (Split Plate Bearing Puller), j 24433 (Pinion Cone and Side Bearing Installer), j 37624 (Pinion Bearing Installer), j 8092 (Universal Driver Handle - 3/4 in - 10), j 8608 (Rear Pinion Bearing Installer), and j 8614-01 (Flange and Pulley Holding Tool). Workers should first elevate the vehicle before taking out the Differential unit followed by the pinion gear bearing retainer, pinion yoke, oil seal, and outer Pinion Bearing. Enso and collapsible spacer must be removed before the j 22912-01 and hydraulic press extract the inner Pinion Bearing. A hammer along with a brass drift should be used to eliminate both the outer and inner Pinion Bearing cups. The procedure for installing pinion gear pilot bearing requires the j 22761 tool followed by an installation sequence of the inner Pinion Bearing cup using j 37624 and j 8092 then the outer Pinion Bearing cup needs to be installed with j 8608 and j 8092. After installing the inner Pinion Bearing with j 24433 you should add a new collapsible spacer before lubricating the pinion bearings. Feed the outer Pinion Bearing into the retainer and mount a fresh pinion oil seal by using j 22388 before inserting the pinion into its bearing retainer. Warm the pinion yoke splines before applying sealant. Install the yoke afterward and correctly attach it to the pinion shaft by using a soft-faced hammer. Tighten the new pinion nut under j 8614-01 tool torque until the pinion end play reaches its maximum resistance. Place the original shim or a 0.41 mm (0.016 inch) alternative shim when you need to replace the missing j 8614-01. Install the pinion gear bearing retainer onto the axle housing before fastening its bolts to 88 nm (65 ft. Lbs.). The measurement of rotating torque for used pinion bearings should fall within 1.0 to 2.3 nm (10 to 20 inch lbs.) while new pinion bearings should measure between 1.7 to 3.4 nm (15 to 30 inch lbs.). You should use the j 8614-01 torque wrench to increase pinion nut tightening steps until reaching the required specification torque. Rotating the pinion several times following torque confirmation helps bear in a proper position but rechecking the torque might be necessary for adjustment. To complete the task you must restore the Differential assembly while adjusting the side bearing preload and selecting drive pinion shims and adjusting backlash before filling with lubricant and returning the vehicle to the ground.

Related GMC Yukon XL 2500 Parts

Browse GMC Yukon XL 2500 Pinion Bearing by Years

2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000