Make sure this part fits

GM 21998965
Hub & Bearing, Rear

2006-2011 GM

Customer Questions & Expert Answers (13)
GM 21998965 Hub & Bearing, Rear
  • Part Description
    Hub, Rear Wheel; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub
  • Position
    Rear
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Buick LucerneCX, CXL, CXL Special Edition, CXS, Super6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 21998965 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 21998965 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel hub and bearing on Buick Lucerne? Posted by Customer
    A:
    Before starting the Wheel Bearing and hub replacement job you need to lift and support the vehicle. Check off the tire then wheel followed by detaching the brake rotor. Detach the electrical connector for the Wheel Bearing/hub unit. Use a socket wrench to remove the Wheel Bearing/hub retaining bolts, then slide out the Wheel Bearing/hub lower part together with the brake shield from the lower Control Arm. Before adding the hub and bearing you should clean both sides of the Control Arm and the inner retaining cavity. Place the brake shield and Wheel Bearing/hub unit onto the Control Arm while ensuring to torque Wheel Bearing/hub bolts to 68 n.m (50 lb ft). Connect the wheel electrical plug first then install the brake rotor piece followed by putting back the wheel and tire then lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel hub on Buick Lucerne? Posted by Customer
    A:
    Simply jack the vehicle upward and take away the tire and wheel then brake rotor for easy access to the wheel bearing/hub. Before removing the wheel bearing/hub lower you need to disconnect its electrical connector and remove both its retaining bolts. Clean both the Control Arm and hub bore after taking away the brake shield from the lower Control Arm for new part installation. You should install the brake shield onto the Control Arm and fasten the wheel bearing/hub according to our service precautions. Put back the wheel bearing/hub electrical connector while torquing the wheel bearing/hub retaining bolts to 68 n.m (50 lb ft). Complete the job by placing the brake rotor back then reinstalling the tire and wheel before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear wheel bearing and hub on Buick Lucerne? Posted by Customer
    A:
    Start replacement work by lifting and placing support underneath the vehicle. Uninstall the wheel and tire then take off the brake rotor. Disconnect the Wheel Bearing/hub electrical connector and remove its bolts to pull out the Wheel Bearing/hub lower and the brake shield from the lower Control Arm. Wash both sides of the Control Arm as well as the hub area before you assemble the parts. Place the brake shield in its position and put the Wheel Bearing/hub to the Control Arm. Secure the Wheel Bearing/hub bolts to 68 n.m (50 lb ft) at their tightest setting. Reattach the wheel/hub wire and put back on the brake rotor before replacing the tire and wheel assembly below the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step to replace the front wheel bearing and hub for the 2008 Buick Lucerne? Posted by Customer
    A:
    First raise and support the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be removed next for the 2008 Buick Lucerne? Posted by Customer
    A:
    Remove the drive axle nut.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Hub
    Q:
    What should be noted when removing the wheel bearing/hub retaining bolts for the 2006 Buick Lucerne? Posted by Customer
    A:
    The hub and bearing should be replaced only as an assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What is the next step after cleaning the control arm for the 2009 Buick Lucerne? Posted by Customer
    A:
    Install the brake shield and the wheel bearing/hub to the control arm.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be applied to the steering knuckle bore before installation for the 2010 Buick Lucerne? Posted by Customer
    A:
    Apply a thin layer of grease.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What needs to be disconnected next for the 2007 Buick Lucerne? Posted by Customer
    A:
    Disconnect the antilock brake system (ABS) front wheel speed sensor connector and unclip it from the dust shield.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be done with the new drive axle nut for the 2007 Buick Lucerne? Posted by Customer
    A:
    Install the new drive axle nut to draw the wheel bearing/hub onto the axle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Hub
    Q:
    What are the final steps after installing the new wheel bearing and hub for the 2007 Cadillac DTS? Posted by Customer
    A:
    Reinstall the brake rotor, reconnect the ABS sensor wire connector, put the tire and wheel back on, and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Bearing
    Q:
    What should be removed after raising for the 2006 Cadillac DTS? Posted by Customer
    A:
    The tire and wheel, followed by the brake rotor.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Hub
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Hub & Bearing, Rear 21998965 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 21998965 Hub & Bearing, Rear is available in the market under the name GM Wheel Bearing, Wheel Hub. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 21998965 Hub & Bearing, Rear fits certain Cadillac DTS models, as well as Buick Lucerne models.
The original GM component designated by manufacturer part number 21998965 maintains top performance when functioning as the Hub, Rear Wheel; Wheel Bearing and Hub Assembly; Wheel Bearing & Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub unit at its Rear. The component 21998965 is constructed from durable material and its dimensions span 8.3 x 7.2 x 7.2 inches while weighing 8.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hub & Bearing Assembly. The part 21998965 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 21998965. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.