Make sure this part fits

GM 19300024
Strut

2006-2011 GM

Customer Questions & Expert Answers (13)
GM 19300024 Strut
GM 19300024 Strut
  • Part Description
    Strut Kit, Front And Rear Suspension; Shock Absorber
  • Position
    Front
  • Replaces
    15211374
  • Manufacturer
    General Motors
Make sure this part fits
$673.39 MSRP: $1306.92
You Save: $633.53 (49%)
Ships in 1 Business Day
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2011 Buick LucerneCX, CXL, CXL Special Edition, CXS, Super6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19300024 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19300024 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace a Shock Absorber (FE1, FE3) on Cadillac DTS? Posted by Customer
    A:
    Starting the Shock Absorber (FE1, FE3) replacement requires vehicle raising and stable support. Begin by removing the wheel followed by the tire then jack the Control Arm into position for support. Detach the electronic level control air tube and shock electrical connector from the Control Arm while removing all wires from the Control Arm. The Shock Absorber needs removal by unbolting its two connections to the Control Arm before pulling out the trunk trim to reveal access to the upper shock. First detach the upper shock dust cover before you can reach the two nuts along with the shock reinforcement and proceed with the Shock Absorber extraction from the vehicle. Begin installation by placement of the new shock onto the vehicle before mounting its upper component. Set the shock reinforcement and two nuts into their places before securing them at 25 n.m (18 lb ft). Install the shock cover followed by proper placement of the trunk trim. Add lower shock bolts to their positioning and tighten them to 25 n.m (18 lb ft). Afterward, join electronic air control air tube and electrical connector to the Control Arm (FE3 and FE45) routing wiring properly. Fasten the wheel with tire in place while tightening each wheel nut to 125 n.m (80 lb ft). First allow the alc system to perform the arc by enabling the ignition and waiting 45 seconds during which the shock absorbers receive residual pressure. Finally, lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    What size drill bit should be used to drill the first hole for the 2010 Buick Lucerne? Posted by Customer
    A:
    A 5 mm (3/16 in) drill bit.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How should the shock absorber be positioned during the process for the 2006 Buick Lucerne? Posted by Customer
    A:
    Clamp the shock absorber horizontally in a vise with the shock absorber rod fully extended.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How should the control arm be supported for the 2008 Buick Lucerne? Posted by Customer
    A:
    Support the control arm with a jack stand.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    Where should you make the first indentation on the shock absorber tube for the 2009 Buick Lucerne? Posted by Customer
    A:
    Make an indentation 10 mm (0.4 in) from the bottom of the tube using a centerpunch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What bolts need to be tightened during installation for the 2009 Buick Lucerne? Posted by Customer
    A:
    The lower shock absorber retaining bolts, also to 25 Nm (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What is the torque specification for the lower shock absorber retaining bolts for the 2007 Buick Lucerne? Posted by Customer
    A:
    25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    How should the shock absorber be positioned for drilling for the 2006 Cadillac DTS? Posted by Customer
    A:
    Clamp the shock absorber in a vise horizontally with the shock absorber rod fully extended.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What should be connected to the shock after installing the lower shock bolts for the 2010 Cadillac DTS? Posted by Customer
    A:
    Connect the electronic air control air tube to the shock.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What needs to be disconnected from the shock for the 2007 Cadillac DTS? Posted by Customer
    A:
    Disconnect the electronic level control air tube from the shock.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What should be done with the wiring for the 2009 Cadillac DTS? Posted by Customer
    A:
    Route the wiring on the control arm (FE3 and FE45).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    Q:
    What is the first step to replace the shock absorber (FE7) for the 2008 Cadillac DTS? Posted by Customer
    A:
    Raise the vehicle and support it securely.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Shock Absorber
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Strut 19300024 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19300024 Strut is available in the market under the name GM Shock Absorber. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19300024 Strut fits certain Cadillac DTS models, as well as Buick Lucerne models.
The original GM component designated by manufacturer part number 19300024 maintains top performance when functioning as the Strut Kit, Front And Rear Suspension; Shock Absorber unit at its Front. The component 19300024 is constructed from durable material and its dimensions span 28.4 x 10.6 x 10.1 inches while weighing 14.20 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 19300024 has available replacement options 15211374. Each vehicle needs 2 units of the part marked as SKU 19300024. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.