Make sure this part fits

GM 19354130
Hinge Assembly, Rear Driver Side

2000-2007 GM

Customer Questions & Expert Answers (21)
GM 19354130 Hinge Assembly, Rear Driver Side
  • Part Description
    Hinge Kit, Rear Side Door (Body Side); Door Hinge
  • Position
    Rear Driver Side
  • Replaces
    12476449
  • Manufacturer
    General Motors
Make sure this part fits
$159.94 MSRP: $239.11
You Save: $79.17 (34%)
Ships in 1-3 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2006 Cadillac EscaladeBase8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2003-2006 Cadillac Escalade ESVBase8 Cyl 6.0 L GAS
    2002-2006 Cadillac Escalade EXTBase8 Cyl 6.0 L GAS
    2002-2006 Chevrolet Avalanche 1500Base, LS, LT, North Face, On Road Edition, WBH, Z66, Z718 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2002-2006 Chevrolet Avalanche 2500Base, LS, LT8 Cyl 8.1 L GAS
    2001-2007 Chevrolet Silverado 1500Base, LS, LT, LTZ, SS, WT, Z71 Off-Road6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2007 Chevrolet Silverado 1500 ClassicLS, LT, SS, WT6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2005-2006, 2001-2003 Chevrolet Silverado 1500 HDBase, LS, LT8 Cyl 6.0 L GAS
    2007 Chevrolet Silverado 1500 HD ClassicLT8 Cyl 6.0 L GAS
    2001-2004 Chevrolet Silverado 2500Base, LS, LT, WT8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19354130 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19354130 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be applied to all bare metal surfaces for the 2004 Cadillac Escalade ESV? Posted by Customer
    A:
    An approved anti-corrosion primer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done after installing each stud for the 2002 Cadillac Escalade? Posted by Customer
    A:
    Draw the stud tight through the pillar using the supplied nuts and repeat for the remaining stud locations.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What size hole should be drilled at the pilot locations for the studs for the 2004 Cadillac Escalade EXT? Posted by Customer
    A:
    Drill an 11.5 mm (29/64 in) hole at the pilot locations.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done if the hinge is difficult to remove for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Use a chisel to separate the hinge from the pillar and then remove the hinge.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How do you position the service hinge for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Position the service hinge within the scribe marks on the door and center punch each hole location according to the service hinge.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done with the existing hinge before removal for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Eliminate any excess sealer around the existing hinge and mark its location on the hinge pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done after marking the welds for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Center punch each weld mark and drill through the hinge base at each punch location using a 13 mm (1/2 in) rotabroach hole saw.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done after cleaning the pillar surface for bodyside hinge replacement for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Position the service hinge, center punch stud locations, drill pilot holes, and then drill for the studs.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the final step after removing each service nut for the 2004 Chevrolet Silverado 1500? Posted by Customer
    A:
    Apply a full-bodied caulk to the entire hinge mounting surface for a proper seal, then install the hinge to the pillar using the supplied nuts, tightening them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the final step after removing each service nut for the 2004 Chevrolet Silverado 2500? Posted by Customer
    A:
    Apply a full-bodied caulk to the entire hinge mounting surface for a proper seal, then install the hinge to the pillar using the supplied nuts, tightening them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done to the bare metal surfaces for the bodyside hinge for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Clean and prepare all bare metal surfaces, apply approved anti-corrosion primer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the final step after removing each service nut for the 2002 Chevrolet Suburban 2500? Posted by Customer
    A:
    Apply a full-bodied caulk to the entire hinge mounting surface for a proper seal, then install the hinge to the pillar using the supplied nuts, tightening them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the process for positioning the service hinge for the 2001 Chevrolet Suburban 1500? Posted by Customer
    A:
    Position the service hinge within the scribe marks on the door and center punch each hole location according to the service hinge.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How do you install the studs for the 2000 Chevrolet Suburban 1500? Posted by Customer
    A:
    Feed fish wire through the hinge and stud hole, install the stud into the wire end, pull it into position, and secure it with the supplied nuts.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What are the final steps after installing the hinge for the 2004 Chevrolet Silverado 3500? Posted by Customer
    A:
    Apply the sealers, refinish the metal surfaces as necessary, and reinstall and align all related panels and components.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the first step to replace the rear door side hinge for the 2006 GMC Yukon? Posted by Customer
    A:
    Begin by removing the related panel and components.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How do you locate the welds attaching the hinge to the pillar for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Lightly hand-sand the existing hinge with 100 grit or finer sandpaper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How is the stud installed for the 2004 GMC Yukon XL 2500? Posted by Customer
    A:
    Feed fish wire through the hinge, the hinge stud hole, and out of the conduit hole in the pillar, then install the stud into the wire end and pull it into position.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done to the existing hinge before removal for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Eliminate any excess sealer around the existing hinge and mark its location on the hinge pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done after removing the hinge for the 2004 GMC Sierra 1500? Posted by Customer
    A:
    Clear all remaining weld from the pillar surface for a flush fit of the service hinge and repair any damage to the pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Hinge Assembly, Rear Driver Side 19354130 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19354130 Hinge Assembly, Rear Driver Side is available in the market under the name GM Door Hinge. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19354130 Hinge Assembly, Rear Driver Side fits certain Chevrolet Tahoe, Silverado 1500, Silverado 2500 HD models, as well as GMC Sierra 1500, Yukon, Sierra 2500 HD. Additionally, it is compatible with Cadillac Escalade, Escalade ESV, Escalade EXT models.
The original GM component designated by manufacturer part number 19354130 maintains top performance when functioning as the Hinge Kit, Rear Side Door (Body Side); Door Hinge unit at its Rear Driver Side. The component 19354130 is constructed from durable material and its dimensions span 5.1 x 5.1 x 11.2 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hinge; Hinge Kit, Door Hinge. The part 19354130 has available replacement options 12476449. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.