GM 15731502
Muffler W/Tpipe Insulator

Vehicle elevation and support are the first steps before replacing an Exhaust Hanger for dual exhaust systems. Use protective goggles along with gloves when performing the task. Extract the transmission bolts from the Exhaust Hanger followed by using a suitable pry bar to disconnect the hanger pin from its insulator. Install the exhaust pipe hanger pins into the Exhaust Hanger insulator before using the hanger to fix onto the transmission. Affix the Exhaust Hanger bolts before screwing them to 17 nm (13 ft. Lbs). Before lowering the car check that every exhaust component maintains proper alignment along with correct clearance between elements.

First, raise and support the vehicle securely to replace the Exhaust Hanger in a dual exhaust system. Unbolt the transmission Exhaust Hanger, gently pry the hanger pin away from Exhaust Hanger insulator using a proper pry bar. Install exhaust pipe hanger pins on the Exhaust Hanger insulator and fix the Exhaust Hanger to the transmission after removing the hanger from the vehicle. Make sure to install the Exhaust Hanger bolts and torque them to 17 nm (13 ft. Lbs.). Lastly, ensure the exhaust system and position/ alignment of all components are appropriate before dropping the car.

Vehicle elevation and support are the first steps before replacing an Exhaust Hanger for dual exhaust systems. Use protective goggles along with gloves when performing the task. Extract the transmission bolts from the Exhaust Hanger followed by using a suitable pry bar to disconnect the hanger pin from its insulator. Install the exhaust pipe hanger pins into the Exhaust Hanger insulator before using the hanger to fix onto the transmission. Affix the Exhaust Hanger bolts before screwing them to 17 nm (13 ft. Lbs). Before lowering the car check that every exhaust component maintains proper alignment along with correct clearance between elements.

You should first support and raise the vehicle before commencing any repair or service of the Exhaust Pipe/muffler hanger. The first step involves removing protective shields when needed before extracting the rear exhaust system together with the Catalytic Converter and front pipe. Motorists should remove the Exhaust Hanger bracket bolts first and then the Exhaust Hanger bracket for automatic transmission vehicles and for manual transmission vehicles the order is Exhaust Hanger bracket bolts then Exhaust Hanger bracket. You should start installation by placing the Exhaust Hanger bracket while adhering to the fastener notice in service precautions. Tighten the Exhaust Hanger bracket bolts to 12 nm using 106 inch lbs when working with automatic transmission units while manual transmission units require a torque of 14 nm or 10 ft. Lbs. Proceed with the installation of the front pipe and Catalytic Converter while incorporating the rear exhaust system. The protective shields should be installed when required. Take off the safety stands before lowering the vehicle to completion.

Vehicle elevation and support are the first steps before replacing an Exhaust Hanger for dual exhaust systems. Use protective goggles along with gloves when performing the task. Extract the transmission bolts from the Exhaust Hanger followed by using a suitable pry bar to disconnect the hanger pin from its insulator. Install the exhaust pipe hanger pins into the Exhaust Hanger insulator before using the hanger to fix onto the transmission. Affix the Exhaust Hanger bolts before screwing them to 17 nm (13 ft. Lbs). Before lowering the car check that every exhaust component maintains proper alignment along with correct clearance between elements.

Vehicle elevation and support are the first steps before replacing an Exhaust Hanger for dual exhaust systems. Use protective goggles along with gloves when performing the task. Extract the transmission bolts from the Exhaust Hanger followed by using a suitable pry bar to disconnect the hanger pin from its insulator. Install the exhaust pipe hanger pins into the Exhaust Hanger insulator before using the hanger to fix onto the transmission. Affix the Exhaust Hanger bolts before screwing them to 17 nm (13 ft. Lbs). Before lowering the car check that every exhaust component maintains proper alignment along with correct clearance between elements.

Vehicle elevation and support are the first steps before replacing an Exhaust Hanger for dual exhaust systems. Use protective goggles along with gloves when performing the task. Extract the transmission bolts from the Exhaust Hanger followed by using a suitable pry bar to disconnect the hanger pin from its insulator. Install the exhaust pipe hanger pins into the Exhaust Hanger insulator before using the hanger to fix onto the transmission. Affix the Exhaust Hanger bolts before screwing them to 17 nm (13 ft. Lbs). Before lowering the car check that every exhaust component maintains proper alignment along with correct clearance between elements.