GM 15083095
Switch

The first step to replace the heated seat switch in the front entails front door trim panel removal. First disconnect the electrical connector before you unfasten retaining clips on the front seat heater switch assembly for switch removal. Seating the new front seat heater switch assembly onto the front trim panel requires pressure to insert it until the assembly is completely set. You should first replace the electrical connector on the front seat heater switch assembly before securing the front trim panel into position.

The first step to change the heated seat switch in the rear demands removal of the end panel from the center console together with disconnecting electrical connections. Begin by unfastening the seat heater switch retaining screws before extracting the switch from the vehicle. Deck the heated seat switch onto the console panel and fix it with the retaining screw by tightening it to 1.6 N.m (14 lb in) according to the Fastener Notice in Service Precautions. Toward the end of installation you need to reattach the electrical connector followed by reinstalling the center console end panel.

Starting the heated seat switch replacement process begins by detaching the electrical connector from the front door trim panel and then taking out the panel. The technician should disconnect the electrical connector and remove the front seat heater switch assembly by unclipping its retaining springs. This will reveal the switch which they can remove. Install the front seat heater switch assembly by fully seating it in the front trim panel after which you can connect its electrical connector and return the front trim panel.

When replacing the front heated seat switch start by taking out the front door trim panel followed by disconnecting its electrical connector. Start by disengaging retaining clips from the front seat heater switch assembly and afterward extract the switch completely until you remove the assembly. Installation starts with fitting the front seat heater switch assembly into the front trim panel until total seating then using the electrical connector to join the assembly followed by front trim panel replacement.

Before you begin replacing the rear heated seat switch you need to remove the center console end panel followed by disconnecting its electrical connector. The switch removal begins with unfastening the seat heater switch retaining screws and then extracting the switch from inside the vehicle. Follow the Fastener Notice in Service Precautions and then place the switch onto the console panel before securing the retaining screw to 1.6 N.m (14 lb in). Next reboot the electrical connection followed by reinstalling the center console end panel.

You should begin the heated seat switch replacement task by removing the center console end panel before disconnecting the electrical connection. Starting with the heated seat switch retaining screws the switch should be detached from the vehicle. Position the switch on the console panel before using the retaining screw to secure it according to the Fastener Notice in Service Precautions with a torque of 1.6 N.m (14 lb in). Reinstall the center console end panel after connecting its electrical connector.

The first step to replace the heated seat switch in the rear unit requires removing the center console end panel followed by disconnecting its electrical connector. After disconnecting the electrical connector from the center console end panel the initial step should be to remove the switch retaining screws followed by extracting the switch from the vehicle. The installation process requires placing the switch on the console panel before securing it with the retaining screw that needs to be tightened to 1.6 N.m (14 lb in) as stated in Service Precautions Fastener Notice. You should reattach the electrical connector afterward before replacing the center console end panel.

Disconnect the electrical connector.

Install the new assembly by pressing it into the front trim panel until it is fully seated.

Remove the front door trim panel and disconnect the electrical connector.

Press the front seat memory switch assembly into the front trim panel until it is fully seated.

Remove the power seat switch bezel from the seat.

Remove the power seat switch bezel from the seat.

Tighten them to 2 N.m (18 lb in).

Remove the power seat switch to bezel screws.

Take out the front seat memory switch assembly.

Remove the center console end panel and disconnect the electrical connector.

Begin by removing the front door trim panel.

Remove the front door trim panel and disconnect the electrical connector.

Take out the front seat memory switch assembly.

Position the lumbar switch onto the power seat switch bezel and ensure to follow the Fastener Notice in Service Precautions.

Release the retaining clips of the front seat memory switch assembly to remove the switch.

Install the new assembly by pressing it into place on the front trim panel until it is completely seated.

Take out the lumbar switch screws from the bezel and then remove the lumbar switch.