How to replace the front brake calipers on a 2.2L engine (without RPO LNF) on 2009 Chevrolet Cobalt?

Before starting brake caliper replacement (without RPO LNF) on 2.2l engines check the brake master cylinder reservoir fluid level. Drain fluid when the level is above halfway. Support the vehicle up and remove the wheel tire set when ready. Prevent the rotor from moving with two wheel nuts when you fasten them by hand to opposite wheel studs. Depress the brake caliper piston toward the brake rotor using a large c-clamp to push the piston through until caliper removal. Unbolt the brake hose-to-caliper connection and pull out the brake hose. Separate the 2 copper brake hose gaskets that may remain stuck to the caliper or hose. Install protection devices to the openings before you remove the brake caliper guide pin bolts and pull the caliper off the bracket. Verify guide pin flexibility and check the quality of boot and boot surrounds; replace defective parts if any restrictions, loosening, or damage is found. Fit the brake caliper on its bracket before inserting the guide pin bolts and fastening them to 34 nm (25 lb ft). Put new copper brake hose gaskets in place and secure the brake hose back onto its location with the bolt while tightening it to 48 nm (35 lb ft). Release huglecion pressure from brake lines to start. Unscrew the wheel nuts during replacement and install the tire-wheel combination. Lower the vehicle and press the Brake Pedal to 2/3 of its range while engine is off then let go slowly. Retighten the Brake Pedal 15 seconds later until it performs firmly to guarantee proper positioning of the brake pads and caliper pistons.

OEM 2009 Chevrolet Cobalt Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2009 Chevrolet Cobalt Caliper, Passenger Side
Part Number: 25900764
$293.01 MSRP: $573.68
You Save: $280.67 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 9.50 Pounds
- Item Dimensions: 6.2 x 12.6 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25900764
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- Base, LS, LT, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet Cobalt Caliper, Driver Side
Part Number: 25900763
$337.36 MSRP: $654.76
You Save: $317.40 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 10.30 Pounds
- Item Dimensions: 11.6 x 11.3 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25900763
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- Base, LS, LT, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet Cobalt Caliper, Driver Side
Part Number: 25902073
Product Specifications
- Other Name: Caliper Kit, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Item Weight: 2.30 Pounds
- Item Dimensions: 9.5 x 8.1 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25902073
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS
View related parts
2009 Chevrolet Cobalt Caliper, Red Line, Passenger Side
Part Number: 19368938
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Replaces: 22687792
- Item Weight: 10.30 Pounds
- Item Dimensions: 9.3 x 7.4 x 5.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19368938
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet Cobalt Caliper, Red Line, Driver Side
Part Number: 19368937
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaces: 22687791
- Item Weight: 7.50 Pounds
- Item Dimensions: 9.2 x 7.3 x 5.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19368937
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet Cobalt Caliper, Passenger Side
Part Number: 25902074
Product Specifications
- Other Name: Caliper Kit, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Item Weight: 2.30 Pounds
- Item Dimensions: 8.4 x 5.2 x 11.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25902074
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS

2009 Chevrolet Cobalt Brake Calipers

With a comprehensive array of OEM 2009 Chevrolet Cobalt Brake Calipers, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2009 Chevrolet Cobalt Brake Calipers are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2009 Chevrolet Cobalt Parts Questions & Experts Answers

Q: How to replace the front brake calipers on a 2.2L engine (without RPO LNF) on 2009 Chevrolet Cobalt?
A: Before starting brake caliper replacement (without RPO LNF) on 2.2l engines check the brake master cylinder reservoir fluid level. Drain fluid when the level is above halfway. Support the vehicle up and remove the wheel tire set when ready. Prevent the rotor from moving with two wheel nuts when you fasten them by hand to opposite wheel studs. Depress the brake caliper piston toward the brake rotor using a large c-clamp to push the piston through until caliper removal. Unbolt the brake hose-to-caliper connection and pull out the brake hose. Separate the 2 copper brake hose gaskets that may remain stuck to the caliper or hose. Install protection devices to the openings before you remove the brake caliper guide pin bolts and pull the caliper off the bracket. Verify guide pin flexibility and check the quality of boot and boot surrounds; replace defective parts if any restrictions, loosening, or damage is found. Fit the brake caliper on its bracket before inserting the guide pin bolts and fastening them to 34 nm (25 lb ft). Put new copper brake hose gaskets in place and secure the brake hose back onto its location with the bolt while tightening it to 48 nm (35 lb ft). Release huglecion pressure from brake lines to start. Unscrew the wheel nuts during replacement and install the tire-wheel combination. Lower the vehicle and press the Brake Pedal to 2/3 of its range while engine is off then let go slowly. Retighten the Brake Pedal 15 seconds later until it performs firmly to guarantee proper positioning of the brake pads and caliper pistons.