How to replace the rear brake line on Buick LeSabre?

Before working on the brake hose you must safely lift your vehicle and detach the tire and wheel. Use a clean tool to clear all materials from brake hose and pipe fittings before placing a rubber cap to seal the brake pipe end. Twist the brake pipe fitting from the brake hose and put an end plug on it for protection. Separate the brake hose from the bracket by using a flat blade tool, then pull out the brake hose from its bracket and unfasten the brake hose from the caliper while keeping the brake caliper steady. Remove the two copper brake hose gaskets since they resist detachment from the caliper or hose end. Also install a rubber plug into the brake hose to caliper bolt hole. You need to discard the rubber plug before putting on new copper brake hose gaskets when installing the brake hose system. Push the brake hose onto the caliper bolt before tightening it to 44 n.m (32 ft lb). Also make sure the hose remains straight during installation. Connect the brake hose to its bracket and retainer. To join the brake pipe fitting with the brake hose remove the rubber cap from the fitting end and tighten it to 11 lb ft or 15 n.m. Complete the hydraulic brake system bleed then put on the wheel and tires before lowering the vehicle.

How to replace the front brake line on Buick LeSabre?

To install new front brake hose start with lifting and stabilizing the vehicle before taking off the tire and wheel components. You should wipe away dirt and foreign items from both brake parts and put a rubber restraint over the brake pipe end to keep dirt out. Sever the brake pipe connection from the brake hose and secure or seal the pipe end to prevent fluid flow. Unscrew the brake hose retainer with a flat tool, extract the brake hose from its bracket, disconnect the brake hose to caliper bolt and finally remove the brake hose. Get rid of the two copper brake hose gaskets that tend to stick to the caliper or hose end and install a rubber plug into the brake hose caliper bolt opening. Take off the bolt from the strut bracket to get at the hose and take out the hose itself. Install new copper brake hose gaskets by taking the rubber plug off from the brake hose to caliper bolt hole. Mount the brake hose onto the new gaskets and bolt while placing it onto the brake caliper. Tighten the bolt to 44 n.m (32 lb ft). After setting the brake hose in place keep it without any bends or turns because damage might develop. Push the brake hose onto its bracket and fasten the hose retainer. Finally discard the rubber cap on the brake pipe fitting end at the outlet. Secure the brake pipe fitting onto the brake hose by tightening it to 15 n.m (11 lb ft). Afterwards, slot the hose bracket onto the strut assembly and fasten its bolt at 17 n.m (13 lb ft). Let air out of the hydraulic brakes before installing tire and wheel before lowering the vehicle down.

OEM Buick LeSabre Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Lines found

View related parts
Buick LeSabre Flex Hose, Front Part Number: 19173093
$11.60 MSRP: $20.71
You Save: $9.11 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Front
- Replaces: 17999356, 18031819, 22113483
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Brake Hose, Rear Part Number: 19173041
$13.65 MSRP: $24.38
You Save: $10.73 (45%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Line; Hose; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 09757655, 18031766, 9757655
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Flex Hose Part Number: 9757655
$13.65 MSRP: $24.38
You Save: $10.73 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Brake Rear; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaced by: 19173041
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Buick LeSabre | Collector's Edition, Custom, Estate Wagon, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick LeSabre Pressure Hose Part Number: 25528398
$30.86
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Brake Master Cylinder; Hydraulic Hose; Lower Pressure Hose; Hose, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose Part Number: 22113234
$15.37 MSRP: $30.86
You Save: $15.49 (51%)
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Passenger Side Part Number: 25764283
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Driver Side Part Number: 25764282
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre High Pressure Hose Part Number: 25528384
Product Specifications
- Other Name: Hose; Hydraulic Hose; Pressure Hose; Hose, Brake Master Cylinder
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1987-1990 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Passenger Side Part Number: 19366761
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 22163448, 17999966, 22163886
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Rear Part Number: 19366759
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 17999820, 22163668, 22113390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose Part Number: 25522287
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1990 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose Part Number: 22113235
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1993 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Driver Side Part Number: 19366760
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 22163885, 22163447, 17999817
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Rear Part Number: 17999714
Product Specifications
- Other Name: Hose, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1999 Buick LeSabre | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Driver Side Part Number: 17999713
Product Specifications
- Other Name: Hose Assembly-Front Brake (Left); Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick LeSabre Flex Hose, Front Passenger Side Part Number: 17999712
Product Specifications
- Other Name: Hose Assembly-Front Brake (Right); Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 Buick LeSabre | Custom, Limited | 6 Cyl 3.8 L GAS

Buick LeSabre Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick LeSabre parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick LeSabre Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Brake Line is a vital complex that is a part of the Buick LeSabre hydraulic brake assembly where brake fluid is supplied from the master cylinder towards the brake caliper pistons. This critical function helps to sustain the brand prominence and value of Buick LeSabre, which is a phenomenal car that hit the market after the year 1959. This Brake Line is very efficient and safe for everyday use due to features such as; This way, the Brake Line that will be installed will suit the respective LeSabre model or the subsequent model variants, regardless of whether it is the earlier model or the later model. Additional features like prebent kits and stainless steel hoses used for the Brake Line boosts on the aspect of durability due to its non-corrosive characteristic and tight fixing. Using the original metal braid hoses can improve the pedal feel and response as compared to the rubber hose especially when one has to do performance driving. Periodical examination of the Brake Line is advised to rule out any emergence of a leak and enhance the brakes function. Designed and made with quality materials, the Brake Line can be regarded as a perfect fit in the automotive market since it enhances the safety and performance that defines LeSabre model, making the part indispensable for any car owner.

Buick LeSabre Brake Line Parts and Q&A

Flex Hose, Rear
19366759
Q: How to replace the rear brake line on Buick LeSabre?
A:
Before working on the brake hose you must safely lift your vehicle and detach the tire and wheel. Use a clean tool to clear all materials from brake hose and pipe fittings before placing a rubber cap to seal the brake pipe end. Twist the brake pipe fitting from the brake hose and put an end plug on it for protection. Separate the brake hose from the bracket by using a flat blade tool, then pull out the brake hose from its bracket and unfasten the brake hose from the caliper while keeping the brake caliper steady. Remove the two copper brake hose gaskets since they resist detachment from the caliper or hose end. Also install a rubber plug into the brake hose to caliper bolt hole. You need to discard the rubber plug before putting on new copper brake hose gaskets when installing the brake hose system. Push the brake hose onto the caliper bolt before tightening it to 44 n.m (32 ft lb). Also make sure the hose remains straight during installation. Connect the brake hose to its bracket and retainer. To join the brake pipe fitting with the brake hose remove the rubber cap from the fitting end and tighten it to 11 lb ft or 15 n.m. Complete the hydraulic brake system bleed then put on the wheel and tires before lowering the vehicle.
Flex Hose, Front Passenger Side
25764283
Q: How to replace the front brake line on Buick LeSabre?
A:
To install new front brake hose start with lifting and stabilizing the vehicle before taking off the tire and wheel components. You should wipe away dirt and foreign items from both brake parts and put a rubber restraint over the brake pipe end to keep dirt out. Sever the brake pipe connection from the brake hose and secure or seal the pipe end to prevent fluid flow. Unscrew the brake hose retainer with a flat tool, extract the brake hose from its bracket, disconnect the brake hose to caliper bolt and finally remove the brake hose. Get rid of the two copper brake hose gaskets that tend to stick to the caliper or hose end and install a rubber plug into the brake hose caliper bolt opening. Take off the bolt from the strut bracket to get at the hose and take out the hose itself. Install new copper brake hose gaskets by taking the rubber plug off from the brake hose to caliper bolt hole. Mount the brake hose onto the new gaskets and bolt while placing it onto the brake caliper. Tighten the bolt to 44 n.m (32 lb ft). After setting the brake hose in place keep it without any bends or turns because damage might develop. Push the brake hose onto its bracket and fasten the hose retainer. Finally discard the rubber cap on the brake pipe fitting end at the outlet. Secure the brake pipe fitting onto the brake hose by tightening it to 15 n.m (11 lb ft). Afterwards, slot the hose bracket onto the strut assembly and fasten its bolt at 17 n.m (13 lb ft). Let air out of the hydraulic brakes before installing tire and wheel before lowering the vehicle down.