How to replace the outer CV Boot and CV Joint on the wheel drive shaft on Chevrolet Impala?

The replacement of both wheel drive shaft outer joint along with boot requires these essential tools: snap ring pliers (J 8059), earred clamp tool (J 35910), small swage tool (J 41048), a breaker bar and torque wrench. The repair requires snap ring pliers (J 8059), earred clamp tool (J 35910), small swage tool (J 41048), a breaker bar as well as a torque wrench. Begin the repair by cutting out the large boot retaining clamp from the cv joint and discarding it followed by cutting and discarding the small clamp at the halfshaft bar. Keep the boot separate from the race and move it forward along the bar's length. The snap ring pliers (J 8059) should be used to expand the retaining ring's ear holes after wiping cv joint inner race grease before bar removal. After boot removal from the bar you can use a hammer to gently tap the cv joint cage with a brass drift to extract all six chrome alloy balls . Use cleaning solvent to cleanse the cv joint inner and outer race assemblies as well as the cv joint cage and balls completely before drying both the components. Ensure all accumulated grease and harmful substances are eliminated from these parts. Construct an assembly by first fitting a new swage ring onto the joint boot's small end before sliding both components onto the halfshaft bar. Mount the outboard shaft edge into the small swage tool (J 41048) inside a vise so the boot groove on the bar receives the boot. Begin by placing the boot neck in its proper position before tightening bolts manually until they reach a snug fit. Continue by alternating the 180-degree rotation of each bolt until they are both fully bottomed. Heat the service kit grease till it reaches a light consistency before applying it to both inner race and outer race ball grooves. Then guide the inner race into the cage with its retaining ring side facing toward the halfshaft bar. Next insert the chrome balls before filling the cv joint with grease. Position the cage with inner race into the outer race. Seam the cv joint onto the halfshaft bar and check that the outboard boot maintains its proper form before the retaining ring reaches its seat. Use the earred clamp tool (J 35910) with a torque wrench to crimp the boot retaining clamp onto the outboard boot's large diameter. Slide the boot over cv joint outer race and tighten it to 130 ft. Lbs. (176 Nm) using a torque wrench and breaker bar . Verifyclamp ear gap and conduct maintenance as needed.

OEM Chevrolet Impala CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 CV Boots found

View related parts
Chevrolet Impala Outer CV Joint Boot, Front Part Number: 19210864
$39.87 MSRP: $68.46
You Save: $28.59 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Outer Boot; Inner Boot Kit; Outer Boot Kit; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Replaces: 15918509, 19206498
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Inner Boot, Front Part Number: 19259374
$17.80 MSRP: $43.45
You Save: $25.65 (60%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot Kit
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Inner CV Joint Boot, Front Part Number: 19210863
$123.25 MSRP: $195.68
You Save: $72.43 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Inner Boot Kit; Outer Boot Kit; Boots; Boot Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX
View related parts
Chevrolet Impala Outer CV Joint Boot, Front Part Number: 19178957
$90.46 MSRP: $155.36
You Save: $64.90 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Outer Boot; Inner Boot Kit; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Replaces: 19150654, 15855656
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Impala | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Boot Kit, Front Part Number: 15269918
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer CV Joint Boot; Outer Boot; Inner Boot Kit; Boots; Boot Kit, Front Axle
- Position: Front
- Replaces: 89047671
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Outer CV Joint Boot, Front Part Number: 13318003
$19.75 MSRP: $30.94
You Save: $11.19 (37%)
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Boot Kit, Front Part Number: 26073372
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Inner Boot Kit; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2011 Chevrolet Impala | 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Seal Kit Part Number: 26044380
Product Specifications
- Other Name: Boot, Front; Axle Seal; CV Boot; Boot Kit; Outer CV Joint Boot; Inner Boot; Outer Boot; Outer Boot Kit; Boots; Boot
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Inner CV Joint Boot, Front Part Number: 39196364
$21.96 MSRP: $34.40
You Save: $12.44 (37%)
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Boots
- Position: Front
- Replaces: 13333928
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2020 Chevrolet Impala | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Outer CV Joint Part Number: 88965619
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Joint; CV Boot; Inner Boot; Outer Boot Kit; Boots
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Impala | SS | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Boot Kit, Front Part Number: 26044383
Product Specifications
- Other Name: Boot Kit, Front Axle; CV Boot; Outer CV Joint Boot; Outer Boot; Outer Boot Kit; Boots; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2010 Chevrolet Impala | 50th Anniversary Edition, Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Impala Outer CV Joint Boot, Front Part Number: 19177868
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner CV Joint Boot; Inner Boot; Inner Boot Kit; Boots
- Position: Front
- Replaces: 26073374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Chevrolet Impala | Base, LS, LS Sport, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

Chevrolet Impala CV Boot

Want to cut long-term maintenance and repair costs? Choose OEM CV Boot. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala CV Boot includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The CV Boot fitted in Chevrolet Impala vehicles is such an important part that safeguards the CV Joint, which helps in transmitting power from the transaxle to wheels. Some of the CV Joints used in Impala vehicle are the fixed joints situated at the outboard end of the axle and the plunging joints found at the inboard of the axle. More specifically, CV Boot exists to cover and shield the CV Joint to allow it not be accessed by dust and other small particles and also to always ensure that the joint in question is lubricated. It often happens that a CV Joint goes bad because of a damaged CV Boot and it is for that reason that it is critical to inspect the CV Boot from time to time which can help in avoiding such situations as making popping or clicking sounds during turns, and when clunking and vibrating during acceleration.

Chevrolet Impala CV Boot Parts and Q&A

Seal Kit
26044380
Q: How to replace the outer CV Boot and CV Joint on the wheel drive shaft on Chevrolet Impala?
A:
The replacement of both wheel drive shaft outer joint along with boot requires these essential tools: snap ring pliers (J 8059), earred clamp tool (J 35910), small swage tool (J 41048), a breaker bar and torque wrench. The repair requires snap ring pliers (J 8059), earred clamp tool (J 35910), small swage tool (J 41048), a breaker bar as well as a torque wrench. Begin the repair by cutting out the large boot retaining clamp from the cv joint and discarding it followed by cutting and discarding the small clamp at the halfshaft bar. Keep the boot separate from the race and move it forward along the bar's length. The snap ring pliers (J 8059) should be used to expand the retaining ring's ear holes after wiping cv joint inner race grease before bar removal. After boot removal from the bar you can use a hammer to gently tap the cv joint cage with a brass drift to extract all six chrome alloy balls . Use cleaning solvent to cleanse the cv joint inner and outer race assemblies as well as the cv joint cage and balls completely before drying both the components. Ensure all accumulated grease and harmful substances are eliminated from these parts. Construct an assembly by first fitting a new swage ring onto the joint boot's small end before sliding both components onto the halfshaft bar. Mount the outboard shaft edge into the small swage tool (J 41048) inside a vise so the boot groove on the bar receives the boot. Begin by placing the boot neck in its proper position before tightening bolts manually until they reach a snug fit. Continue by alternating the 180-degree rotation of each bolt until they are both fully bottomed. Heat the service kit grease till it reaches a light consistency before applying it to both inner race and outer race ball grooves. Then guide the inner race into the cage with its retaining ring side facing toward the halfshaft bar. Next insert the chrome balls before filling the cv joint with grease. Position the cage with inner race into the outer race. Seam the cv joint onto the halfshaft bar and check that the outboard boot maintains its proper form before the retaining ring reaches its seat. Use the earred clamp tool (J 35910) with a torque wrench to crimp the boot retaining clamp onto the outboard boot's large diameter. Slide the boot over cv joint outer race and tighten it to 130 ft. Lbs. (176 Nm) using a torque wrench and breaker bar . Verifyclamp ear gap and conduct maintenance as needed.