Other Name: Sensor Assembly-Rear Suspension 2 Or 4 Corner Air Leveling; Headlight Level Sensor; Ride Height Sensor; Sensor, Air Suspension Leveling Or Level Control
Position: Rear Passenger Side
Replaces: 23135907
Fits the following Chevrolet Models:
Corvette | 2014-2019 | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
Other Name: Sensor Assembly-Rear Suspension 2 Or 4 Corner Air Leveling; Ride Height Sensor; Height Sensor; Sensor, Air Suspension Leveling Or Level Control
Position: Rear Passenger Side
Fits the following Chevrolet Models:
Suburban | 2021-2023 | Commercial, High Country, LS, LT, Premier, RST, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
Tahoe | 2021-2023 | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
Other Name: Sensor Assembly, Electronic Suspension Rear Position (W/Accelerometer); Ride Height Sensor; Rear Sensor; Sensor, Air Suspension Leveling Or Level Control
Position: Rear
Fits the following Chevrolet Models:
Corvette | 2005-2013 | 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
Q: How to replace the front Ride Height Sensor for the electronic suspension on Chevrolet Corvette?
A: The front position sensor replacement for electronic suspension needs a driver to first turn off ignition while using a suitable safety stand to elevate the vehicle. First disconnect the position sensor connector then remove its harness retainer and detach the position sensor link from the control arm link stud before removing the position sensor mounting bolts. Disconnect the position sensor link from its position on the control arm link stud while you take out its mounting bolts. Extract the position sensor unit from its vehicle position. The new position sensor should be installed into the vehicle after following the fastener notice in service precautions. Secure the position sensor mounting bolts with a torque of 3 nm to 26 inch lbs. Connect the position sensor electrical connector after reattaching the position sensor link to its stud on the control arm link. Also reposition the position sensor harness through its retainers. Proceed to reinstall the tire and wheel assembly before lowering down the vehicle.
Q: How to replace the rear right Ride Height Sensor for the electronic suspension on Chevrolet Tahoe?
A: Starting the procedure by lifting the vehicle and removing its wheel will prepare you to replace the right side rear position sensor for the electronic suspension. You should first disconnect the sensor harness connector from the vehicle harness connector before taking off the sensor link from the ball stud. Detach the position sensor by removing its bolts and subsequent removal procedure. The installation procedure requires positioning the new position sensor on the vehicle before securely fastening it with bolts at 12 Nm (106 inch lbs.). Always follow the safety guidelines in service precautions. Secure the connector of the sensor harness to its counterpart in the vehicle and join the sensor link to the ball stud. After completing the installation place the wheel back and bring down the vehicle.
Q: How to replace the Ride Height Sensor (Twist Axle) on Chevrolet Uplander?
A: The first step to replace the Ride Height Sensor (Twist Axle) requires the ELC/TRAILER fuse removal followed by raising and supporting the vehicle. The first step involves disconnecting the Ride Height sensor connector before removing its link from the ball stud. Begin by removing the Ride Height sensor bracket's bolts or screws after taking them out. Remove the Ride Height sensor together with its bracket from the vehicle. The Ride Height sensor along with its bracket need to be returned to their original position on the vehicle and the height sensor bolts/screws should be fastened to 12 N.m (106 lb in). Begin by attaching the Ride Height sensor link to the ball stud followed by connecting its connector to the system. Then lower the vehicle frame before placing back the ELC/TRAILER fuse into its socket.