Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 25814905
Axle Assembly

2006-2008 GM

Customer Questions & Expert Answers (12)
GM 25814905 Axle Assembly
  • Part Description
    Axle; Axle Shaft
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 25814905 Axle Assembly is Ref No. 1 in the diagram below

    2008 GMC Canyon Axle Assembly Diagram for 25814905
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 25814905

  • Vehicle Fitment

    Year Make Model Trim Engine
    2006-2008 Chevrolet ColoradoLS, LT, WT4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
    2006-2008 GMC CanyonSL, SLE, SLT, WT4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25814905 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25814905 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the rear axle shaft on GMC Canyon? Posted by Customer
    A:
    You must begin the rear Axle Shaft replacement procedure by removing the wheels along with tires. Take off the clip that holds the rear Brake Drum only if needed before continuing with rear Brake Drum removal from the vehicle. Start by taking out the rear axle housing cover followed by dismantling the lock pin bolt and extracting the pinion shaft. The next step is to remove both the c-lock of the rear axle followed by pulling out the rear Axle Shaft. Begin installation with the new rear Axle Shaft alignment and afterward attach both the c-lock on the rear axle and the pinion shaft. Put the lock bolt into place then tighten it to 25 n.m (18 lb ft). First replace the rear brake drums before attaching the rear axle housing cover as well as the gasket onto the housing. Finish the axle-fluid filling procedure before putting back the wheel and tire installation.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step after tightening the bolts for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should you do after installing the propeller shaft for the 2008 Chevrolet Colorado? Posted by Customer
    A:
    Install the clamps and retaining bolts, tightening the bolts to 20 N.m (15 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after tightening the bolts for the front propeller U-joint clamps for the 2006 Chevrolet Colorado? Posted by Customer
    A:
    Lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step in the installation process for the 2006 Chevrolet Colorado? Posted by Customer
    A:
    Insert the front wheel drive shaft into the front differential.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What is the first step in the installation process for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Remove the tape or rubber band.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What is the first step to replace the rear axle shaft for the 2008 Chevrolet Colorado? Posted by Customer
    A:
    Begin by removing the tires and wheels.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What should be done after removing the tires and wheels for the 2007 Chevrolet Colorado? Posted by Customer
    A:
    Remove the clip retaining the rear brake drum if necessary, and then take off the rear brake drums from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How should the front propeller shaft be installed for the 2008 GMC Canyon? Posted by Customer
    A:
    Install the front propeller shaft and align the reference marks on the front U-joint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    What should be done after raising and supporting the 2008 GMC Canyon? Posted by Customer
    A:
    Ensure proper alignment of all U-Joints to the transmission, center bearing support, and rear drive axle pinion flange by rotating the propeller shafts until all external clips are aligned.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    Q:
    How do you secure the center bearing during installation for the 2007 GMC Canyon? Posted by Customer
    A:
    Attach the center bearing to the crossmember and secure it with mounting bolts, tightening them to 80 N.m (59 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Drive Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Axle Assembly 25814905 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25814905 Axle Assembly is available in the market under the name GM Axle Shaft, Drive Shaft. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25814905 Axle Assembly fits certain Chevrolet Colorado models, as well as GMC Canyon models.
The original GM component designated by manufacturer part number 25814905 maintains top performance when functioning as the Axle; Axle Shaft unit. The component 25814905 is constructed from durable material. The component is ready in New condition to ensure full compatibility with your vehicle system. The part 25814905 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.