How to replace the rear brake line from the axle to the caliper on 2010 Chevrolet Cobalt?

Higher the vehicle to begin replacing the brake hose that connects axle to caliper. Wipe away dirt and debris from both ends of the brake hose and brake pipe fitting. Before revealing the brake fitting from the hose use the back up wrench to disconnect both parts with protective caps at each end to dodge fluid loss and soiling. Pull out the brake hose from its bracket after taking off the retaining clip from the hose mounting bracket. Take out the brake hose fitting bolt from the caliper and throw away the deteriorated copper brake hose gaskets. Use caps or plugs to seal both the brake caliper opening and brake hose to keep fluid inside during work. First take off caps or plugs before setting new copper brake hose gaskets during installation. Place the brake hose bolts and gaskets on the hose before screwing them by hand until you apply 48 nm (35 lb ft) of torque. Put the brake hose to its mounting bracket and the brake caliper while placing the hose fitting into the notch on the bracket. Use the retaining clip to put the brake hose fitting and push it into place at the rear brake hose end before tightening it to 21 nm (15 lb ft). Put back the tire and wheel set while making sure the hose stays separate from the suspension system parts; fix any accidental contact right away. Complete the job by draining the hydraulic brake system then lowering the vehicle.

OEM 2010 Chevrolet Cobalt Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Lines found

View related parts
2010 Chevrolet Cobalt Flex Hose, Front
Part Number: 19366692
$23.23 MSRP: $70.51
You Save: $47.28 (68%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Replaces: 22716552, 15870413
- Item Weight: 1.30 Pounds
- Item Dimensions: 5.2 x 2.0 x 12.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366692
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2010 Chevrolet Cobalt Flex Hose
Part Number: 19366736
$12.99 MSRP: $31.20
You Save: $18.21 (59%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake Front; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front and Rear
- Replaces: 22706789
- Item Weight: 0.50 Pounds
- Item Dimensions: 6.4 x 3.4 x 2.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19366736
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2010 Chevrolet Cobalt Flex Hose, Rear Driver Side
Part Number: 19366742
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 19331548, 22720042
- Item Weight: 0.60 Pounds
- Item Dimensions: 7.2 x 3.2 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366742
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2010 Chevrolet Cobalt Flex Hose, Rear Passenger Side
Part Number: 19366741
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Replaces: 22720049, 19331547
- Item Weight: 0.60 Pounds
- Item Dimensions: 6.8 x 3.2 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19366741
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
2010 Chevrolet Cobalt Flex Hose, Front
Part Number: 15939642
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Item Weight: 0.80 Pounds
- Item Dimensions: 17.7 x 1.9 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 15939642
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS
View related parts
2010 Chevrolet Cobalt Brake Hose
Part Number: 25820531
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Line
- Position: Rear
- Item Weight: 0.50 Pounds
- Item Dimensions: 11.3 x 3.4 x 0.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 25820531
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2010 Chevrolet Cobalt Submodels:
- SS | 4 Cyl 2.0 L GAS

2010 Chevrolet Cobalt Brake Line

With a comprehensive array of OEM 2010 Chevrolet Cobalt Brake Line, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2010 Chevrolet Cobalt Brake Line are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2010 Chevrolet Cobalt Parts Questions & Experts Answers

Q: How to replace the rear brake line from the axle to the caliper on 2010 Chevrolet Cobalt?
A: Higher the vehicle to begin replacing the brake hose that connects axle to caliper. Wipe away dirt and debris from both ends of the brake hose and brake pipe fitting. Before revealing the brake fitting from the hose use the back up wrench to disconnect both parts with protective caps at each end to dodge fluid loss and soiling. Pull out the brake hose from its bracket after taking off the retaining clip from the hose mounting bracket. Take out the brake hose fitting bolt from the caliper and throw away the deteriorated copper brake hose gaskets. Use caps or plugs to seal both the brake caliper opening and brake hose to keep fluid inside during work. First take off caps or plugs before setting new copper brake hose gaskets during installation. Place the brake hose bolts and gaskets on the hose before screwing them by hand until you apply 48 nm (35 lb ft) of torque. Put the brake hose to its mounting bracket and the brake caliper while placing the hose fitting into the notch on the bracket. Use the retaining clip to put the brake hose fitting and push it into place at the rear brake hose end before tightening it to 21 nm (15 lb ft). Put back the tire and wheel set while making sure the hose stays separate from the suspension system parts; fix any accidental contact right away. Complete the job by draining the hydraulic brake system then lowering the vehicle.