Make sure this part fits

GM 15939642
Flex Hose, Front

2008-2010 GM

Customer Questions & Expert Answers (15)
GM 15939642 Flex Hose, Front
  • Part Description
    Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2010 Chevrolet CobaltSS4 Cyl 2.0 L GAS
    2008-2010 Chevrolet HHRSS, SS Panel4 Cyl 2.0 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 15939642 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15939642 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step to replace the hydraulic clutch hose/pipe for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    First, remove the UBEC.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What is the torque specification for connecting the brake pipe fitting at the rear brake hose for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Tighten it to 21 N.m (15 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done before disconnecting the brake pipe fittings for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Clean all dirt and foreign material from the brake hose ends and brake pipe fittings.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after removing the components from the brake hose for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Remove the brake hose.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How do you disconnect the brake pipe fitting from the brake hose for the 2010 Chevrolet Cobalt? Posted by Customer
    A:
    Use a backup wrench on the hose fitting and disconnect it, capping or plugging both ends to prevent fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    How should the clutch line be installed for the 2010 Chevrolet Cobalt? Posted by Customer
    A:
    Ensure the clutch line locks securely in place by connecting it to the clutch master cylinder and the transaxle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What is the installation process for the clutch line for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Ensure the clutch line locks securely in place, then connect the clutch line to the clutch master cylinder and the transaxle, followed by connecting the clutch hose to the clutch actuator cylinder and the brake master cylinder reservoir.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What should be done after reinstalling the tire and wheel assembly for the 2010 Chevrolet HHR? Posted by Customer
    A:
    Ensure the hose does not contact any part of the suspension; if it does, correct the condition.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the first step to replace the hydraulic clutch hose for the 2009 Chevrolet HHR? Posted by Customer
    A:
    First, remove the UBEC.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What are the final steps after installing the new clutch hose for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Reinstall the UBEC, fill the brake/clutch reservoir with DOT 3 hydraulic fluid to the proper level, and bleed the clutch hydraulic system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What should be done after reinstalling the tire and wheel assembly for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Ensure the hose does not contact any part of the suspension; if it does, correct the condition.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the first step in replacing a brake pipe for the 2008 Chevrolet HHR? Posted by Customer
    A:
    Inspect the area of the brake pipe to be replaced and release it from the retainers as necessary.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be placed under the clutch master cylinder and brake master cylinder reservoir for the 2010 Chevrolet HHR? Posted by Customer
    A:
    Place a shop towel to catch any fluid loss.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What is the first step to replace the rear brake hose for the 2009 Chevrolet HHR? Posted by Customer
    A:
    Begin by raising and supporting the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Flex Hose, Front 15939642 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15939642 Flex Hose, Front is available in the market under the name GM Brake Line, Hydraulic Hose. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15939642 Flex Hose, Front fits certain Chevrolet Cobalt, HHR models.
The original GM component designated by manufacturer part number 15939642 maintains top performance when functioning as the Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line unit at its Front. The component 15939642 is constructed from durable material and its dimensions span 17.7 x 1.9 x 1.8 inches while weighing 0.80 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hose, Hydraulic Brake. The part 15939642 has available replacement options. Each vehicle needs 2 units of the part marked as SKU 15939642. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.