How to replace the rear brake line (Caliper) on Chevrolet Cobalt?

In order to switch the rear brake hose you should first lift and stabilize your vehicle then take off the wheel and tire. Repel any foreign matter and dirt particles from both brake pipe and hose ends. Before removal of the brake hose from its brake pipe connections you should seal both ends with caps or plugs to prevent any fluid leak or contamination. Separate the brake hose mounting bracket by pulling its retaining clip out. Remove the hose from its place. Take out the brake hose fitting bolt from the brake caliper and throw away the copper brake hose gaskets. To protect the system seal the openings of the caliper and hose using cap or plug solutions. Install new copper brake hose gaskets before putting the hose fittings together. Install the brake hose assembly to the brake caliper then tighten the bolt to 48 N.m (35 lb ft) as you place the brake hose gaskets and fitting bolt on the brake hose. Use the brake hose to attach it to the mounting bracket with the hose fitting resting in the notch and fasten it with the retaining clip. To attach the brake pipe fitting at the rear brake hose use a back up wrench and tighten it to 21 N.m (15 lb ft). Replace the tire assembly while making sure the hose stays away from suspension parts. Also fix the hose contact issue when you find it. Before bringing the vehicle down lower the hydraulic system through bleeding steps.

OEM Chevrolet Cobalt Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Lines found

View related parts
Chevrolet Cobalt Flex Hose
Part Number: 19366736
$12.99 MSRP: $31.20
You Save: $18.21 (59%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake Front; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front and Rear
- Replaces: 22706789
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cobalt Flex Hose, Front
Part Number: 19366692
$23.23 MSRP: $70.51
You Save: $47.28 (68%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Replaces: 22716552, 15870413
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cobalt Flex Hose, Rear Driver Side
Part Number: 19366742
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 19331548, 22720042
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cobalt Brake Hose
Part Number: 25820531
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | SS | 4 Cyl 2.0 L GAS
View related parts
Chevrolet Cobalt Flex Hose, Rear Passenger Side
Part Number: 19366741
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Replaces: 22720049, 19331547
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2010 Chevrolet Cobalt | Base, LS, LT, LTZ, Sport, SS | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Chevrolet Cobalt Flex Hose, Front
Part Number: 15939642
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chevrolet Cobalt | SS | 4 Cyl 2.0 L GAS

Chevrolet Cobalt Brake Line

Our website offers an extensive catalog of genuine Chevrolet Cobalt Brake Line at unbeatable prices. Every OEM Chevrolet Cobalt Brake Line comes with a manufacturer's warranty, an easy return policy, and rapid delivery service. Don't miss out on this great opportunity!

Chevrolet Cobalt Brake Line Parts Questions & Experts Answers

Flex Hose, Rear Driver Side
19366742
Q: How to replace the rear brake line (Caliper) on Chevrolet Cobalt?
A: In order to switch the rear brake hose you should first lift and stabilize your vehicle then take off the wheel and tire. Repel any foreign matter and dirt particles from both brake pipe and hose ends. Before removal of the brake hose from its brake pipe connections you should seal both ends with caps or plugs to prevent any fluid leak or contamination. Separate the brake hose mounting bracket by pulling its retaining clip out. Remove the hose from its place. Take out the brake hose fitting bolt from the brake caliper and throw away the copper brake hose gaskets. To protect the system seal the openings of the caliper and hose using cap or plug solutions. Install new copper brake hose gaskets before putting the hose fittings together. Install the brake hose assembly to the brake caliper then tighten the bolt to 48 N.m (35 lb ft) as you place the brake hose gaskets and fitting bolt on the brake hose. Use the brake hose to attach it to the mounting bracket with the hose fitting resting in the notch and fasten it with the retaining clip. To attach the brake pipe fitting at the rear brake hose use a back up wrench and tighten it to 21 N.m (15 lb ft). Replace the tire assembly while making sure the hose stays away from suspension parts. Also fix the hose contact issue when you find it. Before bringing the vehicle down lower the hydraulic system through bleeding steps.