Make sure this part fits

GM 19366741
Flex Hose, Rear Passenger Side

2004-2010 GM

Customer Questions & Expert Answers (14)
GM 19366741 Flex Hose, Rear Passenger Side
  • Part Description
    Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line
  • Position
    Rear Passenger Side
  • Replaces
    22720049, 19331547
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2010 Chevrolet CobaltBase, LS, LT, LTZ, Sport, SS4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2007-2009 Pontiac G5Base, GT4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2004-2007 Saturn Ion1, 2, 3, Red Line4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19366741 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19366741 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be removed from the hose mounting brackets for the 2005 Chevrolet Cobalt? Posted by Customer
    A:
    Remove the brake hose retaining clips from the hose mounting brackets.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What should be done to prevent fluid loss during the replacement for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Place a shop towel under the clutch master cylinder and brake master cylinder reservoir to catch any fluid loss.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What should be done with the brake hose retaining clips for the 2007 Chevrolet Cobalt? Posted by Customer
    A:
    Remove the brake hose retaining clips from the hose mounting brackets and take the hose out of the mounting brackets.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the final step in the process for the 2010 Chevrolet Cobalt? Posted by Customer
    A:
    Finally, bleed the clutch hydraulic system.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What should be done to the brake hose ends and brake pipe fittings before disconnecting for the 2006 Chevrolet Cobalt? Posted by Customer
    A:
    Clean all dirt and foreign material from the brake hose ends and brake pipe fittings.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What are the steps to connect the clutch line during installation for the 2005 Chevrolet Cobalt? Posted by Customer
    A:
    Connect the clutch line to the clutch master cylinder and the transaxle, followed by connecting the clutch hose to the clutch actuator cylinder and the brake master cylinder reservoir.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What is the first step to replace the rear brake hose for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What caution should be taken during the process for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Caution should be taken regarding brake fluid effects on paint and electrical components.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    How do you disconnect the clutch hose for the 2007 Chevrolet Cobalt? Posted by Customer
    A:
    Disconnect the clutch hose from the clutch master cylinder and brake master cylinder reservoir, then disconnect the clutch line at the clutch actuator cylinder and the transaxle, draining the fluid into a suitable container.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What should be checked after reinstalling the tire and wheel assembly for the 2010 Chevrolet Cobalt? Posted by Customer
    A:
    Ensure the hose does not contact any part of the suspension; if it does, correct the condition.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the torque specification for the front brake hose bracket bolt for the 2009 Chevrolet Cobalt? Posted by Customer
    A:
    Tighten it to 25 Nm (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    Q:
    What is the next step after placing the shop towel for the 2006 Chevrolet Cobalt? Posted by Customer
    A:
    Disconnect the clutch hose from the clutch master cylinder and brake master cylinder reservoir.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Hydraulic Hose
    Q:
    What is the final step after completing the installation for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Bleed the hydraulic brake system and lower the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Line
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Flex Hose, Rear Passenger Side 19366741 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19366741 Flex Hose, Rear Passenger Side is available in the market under the name GM Brake Line, Hydraulic Hose. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19366741 Flex Hose, Rear Passenger Side fits certain Chevrolet Cobalt models, as well as Pontiac G5. Additionally, it is compatible with Saturn Ion models.
The original GM component designated by manufacturer part number 19366741 maintains top performance when functioning as the Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line unit at its Rear Passenger Side. The component 19366741 is constructed from durable material and its dimensions span 6.8 x 3.2 x 1.2 inches while weighing 0.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Hose, Hydraulic Brake. The part 19366741 has available replacement options 22720049, 19331547. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.