ChevyParts
My Garage
My Account
Cart
OEM Chevrolet Suburban 1500 Door Hinge
Interior Door Hinge- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
26 Door Hinges found
Chevrolet Suburban 1500 Lower Hinge, Front Part Number: 19354132
$164.44 MSRP: $245.85You Save: $81.41 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Lower Hinge, Front Passenger Side Part Number: 20969646
$135.34 MSRP: $202.34You Save: $67.00 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Lower Hinge, Driver Side Part Number: 12472843
$64.29 MSRP: $92.79You Save: $28.50 (31%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Lower Hinge, Rear Driver Side Part Number: 20876300
$80.83 MSRP: $120.31You Save: $39.48 (33%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Upper Hinge, Rear Driver Side Part Number: 25854397
$82.91 MSRP: $123.41You Save: $40.50 (33%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Upper Hinge, Front Passenger Side Part Number: 25854416
$114.86 MSRP: $171.72You Save: $56.86 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Lower Hinge, Front Driver Side Part Number: 20969645
$121.75 MSRP: $182.02You Save: $60.27 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Upper Hinge, Front Driver Side Part Number: 25854415
$113.33 MSRP: $169.43You Save: $56.10 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Upper Hinge, Rear Passenger Side Part Number: 25854398
$70.74 MSRP: $105.29You Save: $34.55 (33%)Ships in 1-3 Business Days
Chevrolet Suburban 1500 Lower Hinge, Rear Passenger Side Part Number: 20876301
$80.83 MSRP: $120.31You Save: $39.48 (33%)Ships in 1-3 Business DaysChevrolet Suburban 1500 Upper Hinge, Passenger Side Part Number: 12472844
$93.05 MSRP: $179.03You Save: $85.98 (49%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Hinge Assembly, Passenger Side Part Number: 12476452
$222.71 MSRP: $332.97You Save: $110.26 (34%)Ships in 1-2 Business DaysChevrolet Suburban 1500 Lower Hinge, Front Part Number: 19354133
$168.88 MSRP: $252.48You Save: $83.60 (34%)Ships in 1-2 Business Days
Chevrolet Suburban 1500 Hinge Assembly, Rear Driver Side Part Number: 19354130
$159.94 MSRP: $239.11You Save: $79.17 (34%)Ships in 1-3 Business Days
Chevrolet Suburban 1500 Lower Hinge, Driver Side Part Number: 12477499
$55.15 MSRP: $105.20You Save: $50.05 (48%)
Chevrolet Suburban 1500 Hinge Part Number: 15134524
Chevrolet Suburban 1500 Hinge Assembly, Driver Side Part Number: 12476451
$160.60 MSRP: $240.11You Save: $79.51 (34%)Chevrolet Suburban 1500 Hinge Assembly, Rear Passenger Side Part Number: 19354131
$183.76 MSRP: $274.74You Save: $90.98 (34%)
Chevrolet Suburban 1500 Hinge Part Number: 15875510
$52.18 MSRP: $77.67You Save: $25.49 (33%)
| Page 1 of 2 |Next >
1-20 of 26 Results
Chevrolet Suburban 1500 Door Hinge
Want to cut long-term maintenance and repair costs? Choose OEM Door Hinge. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Suburban 1500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Suburban 1500 Door Hinge includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.
Chevrolet Suburban 1500 Door Hinge Parts and Q&A
- Q: How to service and repair the front door hinge on Chevrolet Suburban 1500?A:Service procedures for the front door hinge begin by taking out the door from the body followed by removing extra sealer on the current hinge then marking the hinge pillar location. A 100-grit sandpaper should lightly sand the hinge to reveal its four pillar weld points before center punching these marks while avoiding the pillar itself. Use a 13 mm (1/2 in) rotabroach hole saw or equivalent to drill only through the hinge at each punch location then remove it with a chisel if needed. The pillar surface needs cleaning before fitting the service hinge properly. Repair the damaged area while mounting the service hinge inside its scribe marks and punch center points on both locations of the hinge pillar. Use a 3 mm (1/8 in) pilot hole drill at each marked spot before moving to 11.5 mm (29/64 in) holes for the studs. It is necessary to clean all exposed metal areas before applying anti-corrosion primer. Then insert fish wire (GM P/N 15017229) through the metal hinge structure and its holes. You should use the stud (GM P/N 15017230) to make holes at the wire end then pull the set-up into position before tightening it with supplied nuts (GM P/N 11516746). After completing all stud positions apply full-bodied caulk to each hinge mounting surface to accomplish the needed seal and remove the service nuts. Screw the hinge to the pillar by applying the provided nuts while tightening them to 25 N.m (18 lb ft). Remaining surfaces will need finishing after cleaning and then require sealing and refinishing before the assembly and alignment of all pertinent panels. The door repair needs the same sequence of steps: remove the door, remove surplus sealer, sand the original body hinge, punch center alignment through the weld marks to drill exactly through the hinge base with a 13 mm (1/2 in) rotabroach hole saw. Clean the door surface before fixing any existing damage and then remove and inspect the hinge and washing the surface. Start by preparing the backing plate mounting areas then install the service hinge before punching center points where holes must go. Drill two holes next: One is a 3 mm (1/8 in) pilot hole followed immediately by a 13 mm (1/2 in) main hole. All exposed metal parts require preparation before application of anti-corrosion primer and installation of the hinge mounting surface caulk. After placing the hinge and backing plate with door holes in alignment you should fasten the bolts to 25 N.m (18 lb ft). After performing these tasks finish by applying sealants and refine metal surfaces when needed while installing and adjusting all attached structure components.
- Q: How to replace the front side door hinge on Chevrolet Suburban 1500?A:You should start by taking off every object connected to the front side door hinge and then cut away all unnecessary sealant from around the current hinge before marking its position on the hinge pillar. The existing hinge needs soft sanding using 100-grit or finer sandpaper on the places holding the four door welds so that you can easily drill out the middle points of the welds for removal. Carefully strike center punches at each of the 4 weld locations on the base hinge before drilling to prevent penetrating the door. Use a 13 mm (1/2 in) rotabroach hole saw or equivalent to drill through each punch location on the hinge base before removing the hinge by separating it from the door using a chisel. Remove all remaining weld material from the door surface so the service hinge will have a level fit. The damaged areas from drilling and hinge removal should be repaired before cleaning all surfaces of the mounting areas on the backing plate for proper fit alignment. Place the service hinge inside the scribe marks and mark the hole locations on the door with center punches. Drill a 3 mm (1/8 in) pilot hole at each center punch point while using a drill that matches the exact measures before moving on to drill an 11.5 mm (29/64 in) hole from the pilot marks. All bare metal surfaces must be cleaned before preparing the refinishing process where GM 4901M-D-2000 GM Approved Refinish Materials is consulted to determine suitable products for selection while maintaining separation between paint systems according to paint manufacturer instructions. The entire mounting surface of the hinge demands approved anti-corrosion primer followed by full-bodied caulk to achieve complete sealing. The hinge alignment with door holes must occur before installing the bolts which need a torque of 25 N.m (18 lb ft). After the installation of sealers proceed with the metal surface refinishing process then place all affected panels and components back into position.
Related Chevrolet Suburban 1500 Parts
Chevrolet Suburban 1500 Body Mount Hole Plug
Chevrolet Suburban 1500 Door Check
Chevrolet Suburban 1500 Door Handle
Chevrolet Suburban 1500 Door Lock
Chevrolet Suburban 1500 Door Lock Cylinder
Chevrolet Suburban 1500 Door Seal
Chevrolet Suburban 1500 Liftgate Hinge
Chevrolet Suburban 1500 Tailgate Lift Support
Chevrolet Suburban 1500 Tailgate Lock
Chevrolet Suburban 1500 Trunk Latch
Chevrolet Suburban 1500 Weather Strip
Chevrolet Suburban 1500 Window Motor