Make sure this part fits

GM 19354133
Lower Hinge, Front

1999-2007 GM

Customer Questions & Expert Answers (21)
GM 19354133 Lower Hinge, Front
  • Part Description
    Hinge Kit, Front Side Door (Body Side); Door Hinge
  • Position
    Front
  • Replaces
    12476448, 12477888, 12472842
  • Manufacturer
    General Motors
Make sure this part fits
$168.88 MSRP: $252.48
You Save: $83.60 (34%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2006 Cadillac EscaladeBase8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2003-2006 Cadillac Escalade ESVBase8 Cyl 6.0 L GAS
    2002-2006 Cadillac Escalade EXTBase8 Cyl 6.0 L GAS
    2002-2006 Chevrolet Avalanche 1500Base, LS, LT, North Face, On Road Edition, WBH, Z66, Z718 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
    2002-2006 Chevrolet Avalanche 2500Base, LS, LT8 Cyl 8.1 L GAS
    1999-2007 Chevrolet Silverado 1500Base, Hybrid, LS, LT, LTZ, SS, WT, Z71 Off-Road6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2007 Chevrolet Silverado 1500 ClassicHybrid, LS, LT, SS, WT6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
    2005-2006, 2001-2003 Chevrolet Silverado 1500 HDBase, LS, LT8 Cyl 6.0 L GAS
    2007 Chevrolet Silverado 1500 HD ClassicLT8 Cyl 6.0 L GAS
    1999-2004 Chevrolet Silverado 2500Base, LS, LT, WT8 Cyl 5.3 L GAS, 8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
    View More
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19354133 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19354133 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step after removing each service nut for the 2004 Cadillac Escalade ESV? Posted by Customer
    A:
    Apply a full-bodied caulk to the entire hinge mounting surface for a proper seal, then install the hinge to the pillar using the supplied nuts, tightening them to 25 N.m (18 lb ft).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done to the bare metal surfaces before installation for the 2004 Cadillac Escalade EXT? Posted by Customer
    A:
    Clean and prepare all bare metal surfaces, and apply approved anti-corrosion primer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done before reinstalling and aligning all related panels and components for the 2002 Cadillac Escalade? Posted by Customer
    A:
    Clean and prepare all surfaces as necessary for refinishing, apply sealers, and refinish surfaces as needed.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done if there is damage to the pillar for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Repair any damage to the pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What guidelines should be followed for refinishing materials for the 2003 Chevrolet Avalanche 1500? Posted by Customer
    A:
    Follow the guidelines in GM 4901M-D-2000 for refinishing materials and avoiding paint system combinations.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What preparation is needed for installation for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Clean and prepare the pillar surfaces to ensure a flush fit of the service hinge and fasteners.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should you do after locating the welds for the 2002 Chevrolet Avalanche 2500? Posted by Customer
    A:
    Punch the center of each weld to facilitate removal during drilling.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How should the service hinge be positioned for the 2004 Chevrolet Silverado 2500? Posted by Customer
    A:
    Position the service hinge within the scribe marks and center punch each stud location on the hinge pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the first step in replacing the rear door hinge on the body side for the 2004 Chevrolet Silverado 1500? Posted by Customer
    A:
    Begin by removing all related panels and components.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done with the existing hinge before removal for the 2004 Chevrolet Silverado 3500? Posted by Customer
    A:
    Eliminate any excess sealer around the existing hinge and mark its location on the hinge pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the next step after drilling the pilot holes for the 2002 Chevrolet Suburban 2500? Posted by Customer
    A:
    Drill an 11.5 mm (29/64 in) hole at the pilot locations for the studs.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done before refinishing the metal surfaces for the 2001 Chevrolet Suburban 1500? Posted by Customer
    A:
    Clean and prepare all bare metal surfaces, and consult GM 4901M-D-2000 GM Approved Refinish Materials for recommended products, avoiding the combination of paint systems and adhering to the paint manufacturer's recommendations.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How is the stud installed into the hinge for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Use fish wire (GM P/N 15017229) to install the stud (GM P/N 15017230) into the hinge.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What are the steps for drilling pilot holes for the studs for the 2000 Chevrolet Suburban 1500? Posted by Customer
    A:
    Drill a 3 mm (1/8 in) pilot hole at each location, followed by an 11.5 mm (29/64 in) hole for the studs.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What should be done to the door before installing the service hinge for the 2000 Chevrolet Tahoe? Posted by Customer
    A:
    Repair any damage to the door, clean and prepare the backing plate mounting surfaces.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the process for drilling pilot holes for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Drill a 3 mm (1/8 in) pilot hole at each center punch location, then drill an 11.5 mm (29/64 in) hole at the pilot locations for the studs.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How is the stud installed for the 2001 GMC Yukon XL 1500? Posted by Customer
    A:
    Feed fish wire through the hinge, the hinge stud hole, and out of the conduit hole in the pillar, then install the stud into the wire end and pull it into position.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    How should the service hinge be positioned for the 2004 GMC Sierra 1500? Posted by Customer
    A:
    Position the service hinge within the scribe marks and center punch each stud location on the hinge pillar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What is the next step after locating the welds for the 2006 GMC Yukon? Posted by Customer
    A:
    Center punch each of the 4 weld marks on the original hinge base, taking care not to drill into the door.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    Q:
    What tool is used to drill through the hinge for the 2004 GMC Yukon XL 2500? Posted by Customer
    A:
    A 13 mm (1/2 in) rotabroach hole saw.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Hinge
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Lower Hinge, Front 19354133 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19354133 Lower Hinge, Front is available in the market under the name GM Door Hinge. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19354133 Lower Hinge, Front fits certain Chevrolet Tahoe, Silverado 1500, Silverado 2500 HD models, as well as GMC Sierra 1500, Yukon, Sierra 2500 HD. Additionally, it is compatible with Cadillac Escalade, Escalade ESV, Escalade EXT models.
The original GM component designated by manufacturer part number 19354133 maintains top performance when functioning as the Hinge Kit, Front Side Door (Body Side); Door Hinge unit at its Front. The component 19354133 is constructed from durable material and its dimensions span 5.1 x 5.2 x 11.2 inches while weighing 2.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Upper Hinge; Hinge; Hinge Kit, Door Hinge. The part 19354133 has available replacement options 12476448, 12477888, 12472842. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.