GM 15110641
Lock Assembly, Front Driver Side

The process to replace the rear door latch (Cargo Door Upper) begins by removing the door trim panel then continuing with bolt removal that keeps the latch attached to the door. You should remove the latch while disconnecting the actuator cable assembly until you can take out the latch bolts and completely remove the latch. Begin by linking the actuator cable assembly to the latch after which you should install the bottom two bolts without tightening them. Expose the latch assembly by closing the door to enable self-adjustment and securely bolt these components to 9 N.m (80 lb in force). Open the door to position the upper bolt before tightening it to 9 N.m (80 lb in) and afterward reattach the door trim panel.

The first step in replace a front side Door Lock Actuator requires users to raise the window glass before they take off the door trim panel alongside the water deflector. The front side Door Lock rod extending from the handle retainer clip needs removal along with the manual Door Lock rod from its mounting on the door retainer clips. The rubber plug must be uninstalled to allow access to the outside handle rod retainer and cylinder lock rod disconnection. The next step requires removal of bolts which secure the Door Lock Actuator to the door before extracting the actuator and its control rods as one unit. First disconnect any electrical connector that exists on door locks and then proceed to separate control rods as needed. The installation process requires control rod attachment to the assembly followed by electrical connector joining to the Door Lock Actuator if it is present. Lower the Door Lock Actuator into position on the door before connecting both outside door handle control rod and cylinder lock rod. Secure the Door Lock Actuator bolts to the door. Secure the Door Lock Actuator bolts to the door structure by tightening its screws to 9 n.m (80 lb in). The manual Door Lock receives installments to the door retainer clips followed by an installation of the inside door handle control rod to the lock assembly and the inside Door Lock rod to the handle retainer clip. As the last step install the water deflector then mount the door trim panel before checking the functioning of all involved components.

The process to replace the rear door latch (Cargo Door Upper) begins by removing the door trim panel then continuing with bolt removal that keeps the latch attached to the door. You should remove the latch while disconnecting the actuator cable assembly until you can take out the latch bolts and completely remove the latch. Begin by linking the actuator cable assembly to the latch after which you should install the bottom two bolts without tightening them. Expose the latch assembly by closing the door to enable self-adjustment and securely bolt these components to 9 N.m (80 lb in force). Open the door to position the upper bolt before tightening it to 9 N.m (80 lb in) and afterward reattach the door trim panel.

Insert the rod into the clip on the door latch assembly and close the clip.

Install the door latch into the door, ensuring to tighten the door latch fasteners to 10 N.m (89 lb in).

Install the inside door handle and inspect for proper operation of the door handles before reinstalling the water deflector, door module, and door trim panel.

Install the lock cylinder rod into the door latch and tighten the window run channel fastener to 9 N.m (80 lb in).

Install the door latch into the door, ensuring to tighten the fasteners to 10 N.m (89 lb in).

Tighten these bolts to 9 N.m (80 lb in).

Remove the bolts that secure the latch to the door.

Remove the bolts that secure the latch to the door.

Reconnect the electrical connectors and reinstall the upper and lower trim panels.

Connect the manual door lock to the door retainer clips.

The manual door lock.

The door lock actuator and the control rods.

Remove the latch bolts and the latch itself.

The importance of following the Fastener Notice in Service Precautions.

Install the water deflector, the door trim panel, and inspect the operation of all related components.

Reinstall the water deflector and the door trim panel, and inspect the operation of all related components.

Begin by removing the door trim panel.

Install the latch to the door and tighten the bolts to 9 N.m (80 lb in).

Remove the door trim panel and the water deflector.

Ensure to install the latch to the door while tightening the bolts to 9 N.m (80 lb in).

Reconnect the electrical connectors and reinstall the upper and lower trim panels.

Remove the latch retaining bolts.

Remove the latch retaining bolts.

Begin by removing the door trim panel.

Raise the window and remove the door trim panel, followed by the water deflector.

Remove the latch bolts and the latch itself.

The inside door lock rod.

Reinstall the door trim panel.

Remove the bolts that secure the door lock actuator to the door and take out the door lock actuator along with the control rods as an assembly.

Connect the electrical connectors to the door lock actuator if equipped.

The cylinder lock rod.

Install the door lock actuator to the door.

Connect the control rod for the inside door handle to the lock assembly and the inside door lock rod to the handle retainer clip.

Reinstall the door trim panel.

Reconnect the electrical connector if needed.

Install the water deflector and the door trim panel, and inspect the operation of all related components.

Disconnect the cylinder lock rod.

Remove the latch retaining bolts.

Loosely assemble the bottom two bolts.

Remove the latch retaining bolts.

Disconnect it from the door retainer clips.

Remove the bolts that secure the door lock actuator to the door and take out the door lock actuator along with the control rods as an assembly.

Disconnect the electrical connector from the door lock actuator.

9 N.m (80 lb in).