How to service and repair the front door hinge on 2000 Chevrolet Suburban 1500?

Service procedures for the front door hinge begin by taking out the door from the body followed by removing extra sealer on the current hinge then marking the hinge pillar location. A 100-grit sandpaper should lightly sand the hinge to reveal its four pillar weld points before center punching these marks while avoiding the pillar itself. Use a 13 mm (1/2 in) rotabroach hole saw or equivalent to drill only through the hinge at each punch location then remove it with a chisel if needed. The pillar surface needs cleaning before fitting the service hinge properly. Repair the damaged area while mounting the service hinge inside its scribe marks and punch center points on both locations of the hinge pillar. Use a 3 mm (1/8 in) pilot hole drill at each marked spot before moving to 11.5 mm (29/64 in) holes for the studs. It is necessary to clean all exposed metal areas before applying anti-corrosion primer. Then insert fish wire (GM P/N 15017229) through the metal hinge structure and its holes. You should use the stud (GM P/N 15017230) to make holes at the wire end then pull the set-up into position before tightening it with supplied nuts (GM P/N 11516746). After completing all stud positions apply full-bodied caulk to each hinge mounting surface to accomplish the needed seal and remove the service nuts. Screw the hinge to the pillar by applying the provided nuts while tightening them to 25 N.m (18 lb ft). Remaining surfaces will need finishing after cleaning and then require sealing and refinishing before the assembly and alignment of all pertinent panels. The door repair needs the same sequence of steps: remove the door, remove surplus sealer, sand the original body hinge, punch center alignment through the weld marks to drill exactly through the hinge base with a 13 mm (1/2 in) rotabroach hole saw. Clean the door surface before fixing any existing damage and then remove and inspect the hinge and washing the surface. Start by preparing the backing plate mounting areas then install the service hinge before punching center points where holes must go. Drill two holes next: One is a 3 mm (1/8 in) pilot hole followed immediately by a 13 mm (1/2 in) main hole. All exposed metal parts require preparation before application of anti-corrosion primer and installation of the hinge mounting surface caulk. After placing the hinge and backing plate with door holes in alignment you should fasten the bolts to 25 N.m (18 lb ft). After performing these tasks finish by applying sealants and refine metal surfaces when needed while installing and adjusting all attached structure components.

OEM 2000 Chevrolet Suburban 1500 Door Hinge

Interior Door Hinge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Door Hinges found

View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Driver Side
Part Number: 12472843
$83.12 MSRP: $123.71
You Save: $40.59 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Upper Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 1.60 Pounds
- Item Dimensions: 7.0 x 4.3 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12472843
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Front
Part Number: 19354132
$164.44 MSRP: $245.85
You Save: $81.41 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Front Side Door (Body Side); Door Hinge; Upper Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Front
- Replaces: 12476447, 12477887, 12472841
- Item Weight: 2.50 Pounds
- Item Dimensions: 7.9 x 5.4 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19354132
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Hinge Assembly, Passenger Side
Part Number: 12476452
$204.32 MSRP: $305.48
You Save: $101.16 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 1.30 Pounds
- Item Dimensions: 7.4 x 4.1 x 4.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12476452
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Front
Part Number: 19354133
$168.88 MSRP: $252.48
You Save: $83.60 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Front Side Door (Body Side); Door Hinge; Upper Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Front
- Replaces: 12476448, 12477888, 12472842
- Item Weight: 2.30 Pounds
- Item Dimensions: 5.1 x 5.2 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19354133
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Hinge Assembly, Driver Side
Part Number: 12476451
$160.60 MSRP: $240.11
You Save: $79.51 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 1.30 Pounds
- Item Dimensions: 7.1 x 4.1 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12476451
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Hinge Assembly, Rear Driver Side
Part Number: 19354130
$159.94 MSRP: $239.11
You Save: $79.17 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Door Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Rear Driver Side
- Replaces: 12476449
- Item Weight: 1.30 Pounds
- Item Dimensions: 5.1 x 5.1 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19354130
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Upper Hinge, Passenger Side
Part Number: 12472844
$93.05 MSRP: $179.03
You Save: $85.98 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Lower Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 1.90 Pounds
- Item Dimensions: 6.9 x 4.5 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12472844
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Driver Side
Part Number: 12477827
$12.53 MSRP: $130.36
You Save: $117.83 (91%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 3.30 Pounds
- Item Dimensions: 6.9 x 4.5 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477827
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Hinge
Part Number: 15134524
Product Specifications
- Other Name: Hinge, End Gate Closing; Liftgate Hinge; Door Hinge
- Replaces: 15767489, 15762178
- Item Weight: 0.90 Pounds
- Item Dimensions: 5.5 x 4.5 x 1.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15134524
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Hinge Assembly, Rear Passenger Side
Part Number: 19354131
$183.76 MSRP: $274.74
You Save: $90.98 (34%)
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Door Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Rear Passenger Side
- Replaces: 12476450
- Item Weight: 2.30 Pounds
- Item Dimensions: 5.2 x 5.2 x 11.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19354131
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Passenger Side
Part Number: 12477500
Product Specifications
- Other Name: Hinge, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 4.00 Pounds
- Item Dimensions: 7.1 x 4.6 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477500
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Upper Hinge, Driver Side
Part Number: 12477497
Product Specifications
- Other Name: Hinge, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 4.10 Pounds
- Item Dimensions: 6.1 x 6.1 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477497
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Passenger Side
Part Number: 12477828
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 3.40 Pounds
- Item Dimensions: 7.0 x 4.3 x 4.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477828
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Upper Hinge, Driver Side
Part Number: 12477825
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 3.30 Pounds
- Item Dimensions: 6.8 x 6.6 x 4.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477825
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Upper Hinge, Passenger Side
Part Number: 12477826
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 3.20 Pounds
- Item Dimensions: 6.8 x 6.7 x 4.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477826
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Upper Hinge, Passenger Side
Part Number: 12477498
Product Specifications
- Other Name: Hinge, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Item Weight: 4.10 Pounds
- Item Dimensions: 7.7 x 4.7 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477498
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
2000 Chevrolet Suburban 1500 Lower Hinge, Driver Side
Part Number: 12477499
Product Specifications
- Other Name: Hinge, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Item Weight: 3.90 Pounds
- Item Dimensions: 6.5 x 4.6 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12477499
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2000 Chevrolet Suburban 1500 Submodels:
- Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS

2000 Chevrolet Suburban 1500 Door Hinge

With a comprehensive array of OEM 2000 Chevrolet Suburban 1500 Door Hinge, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 Chevrolet Suburban 1500 Door Hinge are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2000 Chevrolet Suburban 1500 Door Hinge Parts Questions & Experts Answers

Q: How to service and repair the front door hinge on 2000 Chevrolet Suburban 1500?
A: Service procedures for the front door hinge begin by taking out the door from the body followed by removing extra sealer on the current hinge then marking the hinge pillar location. A 100-grit sandpaper should lightly sand the hinge to reveal its four pillar weld points before center punching these marks while avoiding the pillar itself. Use a 13 mm (1/2 in) rotabroach hole saw or equivalent to drill only through the hinge at each punch location then remove it with a chisel if needed. The pillar surface needs cleaning before fitting the service hinge properly. Repair the damaged area while mounting the service hinge inside its scribe marks and punch center points on both locations of the hinge pillar. Use a 3 mm (1/8 in) pilot hole drill at each marked spot before moving to 11.5 mm (29/64 in) holes for the studs. It is necessary to clean all exposed metal areas before applying anti-corrosion primer. Then insert fish wire (GM P/N 15017229) through the metal hinge structure and its holes. You should use the stud (GM P/N 15017230) to make holes at the wire end then pull the set-up into position before tightening it with supplied nuts (GM P/N 11516746). After completing all stud positions apply full-bodied caulk to each hinge mounting surface to accomplish the needed seal and remove the service nuts. Screw the hinge to the pillar by applying the provided nuts while tightening them to 25 N.m (18 lb ft). Remaining surfaces will need finishing after cleaning and then require sealing and refinishing before the assembly and alignment of all pertinent panels. The door repair needs the same sequence of steps: remove the door, remove surplus sealer, sand the original body hinge, punch center alignment through the weld marks to drill exactly through the hinge base with a 13 mm (1/2 in) rotabroach hole saw. Clean the door surface before fixing any existing damage and then remove and inspect the hinge and washing the surface. Start by preparing the backing plate mounting areas then install the service hinge before punching center points where holes must go. Drill two holes next: One is a 3 mm (1/8 in) pilot hole followed immediately by a 13 mm (1/2 in) main hole. All exposed metal parts require preparation before application of anti-corrosion primer and installation of the hinge mounting surface caulk. After placing the hinge and backing plate with door holes in alignment you should fasten the bolts to 25 N.m (18 lb ft). After performing these tasks finish by applying sealants and refine metal surfaces when needed while installing and adjusting all attached structure components.

Related 2000 Chevrolet Suburban 1500 Parts

Alternate Year Models

2001 Chevrolet Suburban 1500 Door Hinge