Other Name: Hose Assembly-Power Steering Gear Inlet; Pressure Hose
Replaced by: 15295840
Fits the following GMC Models:
Sierra 1500 | 2001-2009 | Base, C3, Denali, HT, Hybrid, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
Sierra 1500 HD | 2005-2006, 2001-2003 | SLE, SLT | 8 Cyl 6.0 L GAS
Sierra 2500 | 2001-2004 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS
Sierra 2500 HD | 2001-2010 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L BI-FUEL, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
Sierra 2500 HD Classic | 2007 | SL, SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
Sierra 3500 | 2001-2006 | Base, SL, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
Sierra 3500 Classic | 2007 | SL, SLE, SLT, WT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
Sierra 3500 HD | 2007-2010 | SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
Q: How to Replace a Power Steering Hose in the Fluid Reservoir Outlet on GMC Acadia?
A: Beginning replacement of the power steering fluid reservoir outlet hose requires removing the fuel injector sight shield and draining all possible fluid from the remote power steering fluid reservoir while placing drain pans underneath the vehicle according to need. The power steering fluid reservoir outlet hose requires removal from its points of connection with both the remote power steering fluid reservoir and the Power Steering Pump after clearing any relevant clips. Connect the new power steering fluid reservoir outlet hose to both the Power Steering Pump and remote power steering fluid reservoir while securing the hose along its natural routing with clips. Following the installation process you should clean excess fluid from your vehicle while removing drain pans and filling up the power steering system and bleeding it before reinstalling the fuel injector sight shield.
Q: How to replace the Power Steering Hose without hydroboost on GMC Sierra 1500?
A: The replacement of the Power Steering Cooler pipe/hose without hydroboost begins with front grille removal. Free the retaining clamp from the power steering gear which holds the power steering outlet hose followed by removing the clamp from the Power Steering Pump inlet hose. Next remove the bolts that hold the Power Steering Cooler to the radiator support before taking out the Power Steering Cooler from the vehicle. Place the Power Steering Cooler inside the vehicle before tightening supporting bolts to 5 nm (44 inch lbs.). Secure the power steering outlet hose to the power steering gear through installation of its retaining clamp. The power steering inlet hose must be connected to the Power Steering Pump while installing the holding clamp. The power steering system bleeding will complete followed by hose connection leak inspection before reattaching the front grille.
Q: How to replace the power steering hose inlet with hydroboost on GMC Yukon?
A: A drain pan under the vehicle should be installed first when changing the power steering gear inlet pipe/hose to hydroboost. First remove the power steering gear inlet hose from the Brake Booster after which you must remove it from the power steering gear before taking it out of the vehicle. When installing the hose position the route the same way as before removal then secure the power steering gear inlet hose to the Brake Booster with just hand tight fittings. When installing the power steering gear inlet hose users must mount it to the power steering gear before securing both connecting points at 28 nm (20 ft. Lbs.). Complete the installation process before removing the drain pan from below the vehicle and performing power steering system bleeding.