Make sure this part fits

GM 10424940
Door Actuator, Driver Side

2001-2007 GM

Customer Questions & Expert Answers (14)
GM 10424940 Door Actuator, Driver Side
  • Part Description
    Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator
  • Position
    Driver Side
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2002-2007 Buick RendezvousCX, CX Plus, CXL, CXL Plus, Ultra6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
    2001-2005 Chevrolet VentureBase, LS, LT, Plus, Value, Warner Bros.6 Cyl 3.4 L GAS
    2001-2004 Oldsmobile SilhouetteGL, GLS, Premiere6 Cyl 3.4 L GAS
    2001-2005 Pontiac AztekBase, GT, Rally6 Cyl 3.4 L GAS
    2001-2005 Pontiac MontanaBase6 Cyl 3.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 10424940 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 10424940 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to service and repair the Blend Door Actuator on the left on Buick Rendezvous? Posted by Customer
    A:
    Start the air temperature actuator left service process by taking off the knee bolster as the first step. The defroster door lever needs positioning through vent mode hvac control setting for air temperature actuator access. The service starts by removing the left hand temperature door lever bolt from the hvac module before proceeding to disconnect the left hand temperature door lever spring and left hand temperature door lever . Unplug the left hand air temperature actuator electrical connector while unscrewing the mounting bolts to extract the left hand air temperature actuator. Reinstall the left hand air temperature actuator into position by using the mounting screws that require a torque setting of 1.6 n.m (14 lb in). Reconnect the electrical connector for the left hand air temperature actuator before you install the left hand temperature door lever onto its corresponding location on the left hand temperature door. Make sure the actuator's pin matches the slot on the lever. Secure the left hand temperature door lever spring between its appropriate positions on the lever and hvac module case. Follow this step by installing and tightening the left hand temperature door lever bolt to 0.9 n.m (8 lb in). The knee bolster needs to be reinstalled after the actuators complete their recalibration.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step to replace the right air temperature actuator for the 2004 Buick Rendezvous? Posted by Customer
    A:
    First, remove the I/P compartment.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How should the temperature door lever be installed for the 2003 Buick Rendezvous? Posted by Customer
    A:
    Ensure the pin on the air temperature actuator aligns with the slot in the temperature door lever.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the final step in the process for the 2002 Buick Rendezvous? Posted by Customer
    A:
    Reinstall the knee bolster.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should the HVAC controls be set to for access for the 2006 Buick Rendezvous? Posted by Customer
    A:
    Set the HVAC controls to the vent mode.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step to replace the air temperature actuator for the 2005 Buick Rendezvous? Posted by Customer
    A:
    Remove the knee bolster and set the HVAC controls to the vent mode to position the defroster door lever for access.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should the HVAC controls be set to for access for the 2007 Buick Rendezvous? Posted by Customer
    A:
    Ensure the HVAC controls are set to vent mode to position the defroster door lever for access.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the first step for installation of the new actuator for the 2004 Chevrolet Venture? Posted by Customer
    A:
    Begin by placing the new left hand air temperature actuator in position and securing it with the mounting screws, tightening them to 1.6 N.m (14 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the torque specification for the mounting screws for the 2005 Chevrolet Venture? Posted by Customer
    A:
    Tighten them to 1.6 N.m (14 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    How do you install the new actuator for the 2002 Chevrolet Venture? Posted by Customer
    A:
    Engage the actuator linkage to the left air temperature door lever and install the actuator, ensuring to follow the Fastener Notice in Service Precautions.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What should be done after securing the new actuator for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Reconnect the electrical connector for the actuator.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What is the torque specification for tightening the retaining screws for the 2001 Chevrolet Venture? Posted by Customer
    A:
    Ensure to tighten the retaining screws to 1.6 N.m (14 lb in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    Q:
    What components need to be disconnected and removed from the temperature door for the 2003 Chevrolet Venture? Posted by Customer
    A:
    Disconnect and remove the temperature door lever spring and the temperature door lever.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Blend Door Actuator
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Door Actuator, Driver Side 10424940 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 10424940 Door Actuator, Driver Side is available in the market under the name GM Blend Door Actuator. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 10424940 Door Actuator, Driver Side fits certain Chevrolet Venture models, as well as Buick Rendezvous. Additionally, it is compatible with Pontiac Aztek, Montana and Oldsmobile Silhouette models.
The original GM component designated by manufacturer part number 10424940 maintains top performance when functioning as the Actuator, Air Conditioner Control; HVAC Heater Blend Door Actuator unit at its Driver Side. The component 10424940 is constructed from durable material and its dimensions span 4.3 x 4.1 x 2.2 inches while weighing 0.70 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Actuator; Actuator, A/C Control. The part 10424940 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.