Make sure this part fits

GM 88957230
Outer Boot

2004-2014 GM

Customer Questions & Expert Answers (15)
GM 88957230 Outer Boot
  • Part Description
    Boot Kit, Rear Axle Universal Joint; CV Boot
  • Position
    Rear
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2014 Cadillac CTSBase, Luxury, Performance, Premium, V, Vsport, Vsport Premium6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    2005-2011 Cadillac STSBase, Platinum, V6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is 88957230 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88957230 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the final step in the assembly process for the 2009 Cadillac CTS? Posted by Customer
    A:
    Attach the boot clamp on the boot for the tripot housing and the boot clamp on the boot for the wheel drive, then use the J 35566 - Earless Seal Clamp Tool to close and lock the boot clamp.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What tool is used to remove the boot retaining clamp from the tripot housing for the 2010 Cadillac CTS? Posted by Customer
    A:
    A flat-bladed tool is used to remove the boot retaining clamp from the boot for the tripot housing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you close the inner and outer boot clamps for the 2010 Cadillac CTS? Posted by Customer
    A:
    Close the inner and outer boot clamps using the J 42572 - pliers until the gap measures 1.0 (0.040 in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you secure the wheel drive shaft for the replacement process for the 2008 Cadillac CTS? Posted by Customer
    A:
    Remove the bolt and washer assemblies from the wheel drive shaft, then wrap a shop towel around it and secure it horizontally in a vise.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done if contamination is found in the inner components for the 2009 Cadillac CTS? Posted by Customer
    A:
    Replace the rear wheel drive shaft assembly as these components are not serviced.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the method to remove the outer joint from the axle shaft for the 2009 Cadillac SRX? Posted by Customer
    A:
    Hold the outer joint housing horizontally, place a wood block between the seal and the joint, and strike the block with a hammer to compress the axle shaft retaining clip.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be marked before disassembly for the 2007 Cadillac STS? Posted by Customer
    A:
    Accurately mark the tripot spider position on the wheel drive shaft bar.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the first step to replace the front wheel drive shaft outer joint and seal for the 2007 Cadillac SRX? Posted by Customer
    A:
    Ensure the wheel drive shaft is removed from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done with the clamp before crimping for the 2009 Cadillac SRX? Posted by Customer
    A:
    Position the clamp between the bolts and washers before crimping.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the first step in the assembly process for the 2008 Cadillac STS? Posted by Customer
    A:
    Place a new small seal clamp onto the small end of the inner joint seal and slide it into the boot groove.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What is the first step to replace the front wheel drive shaft inner joint and seal for the 2007 Cadillac SRX? Posted by Customer
    A:
    Ensure the wheel drive shaft has been removed from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be done after removing the boot clamps for the 2009 Cadillac STS? Posted by Customer
    A:
    Take off the tripod housing from the wheel drive shaft.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    What should be inspected before proceeding with assembly for the 2010 Cadillac STS? Posted by Customer
    A:
    The inner CV joint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    Q:
    How do you align the inner race with the cage for the 2010 Cadillac STS? Posted by Customer
    A:
    Insert the inner race at a 90-degree angle and align it with the cage.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Boot
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Outer Boot 88957230 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88957230 Outer Boot is available in the market under the name GM CV Boot. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88957230 Outer Boot fits certain Cadillac CTS, SRX, STS models.
The original GM component designated by manufacturer part number 88957230 maintains top performance when functioning as the Boot Kit, Rear Axle Universal Joint; CV Boot unit at its Rear. The component 88957230 is constructed from durable material and its dimensions span 11.1 x 10.7 x 6.8 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Inner Boot. The part 88957230 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.