GM 15832313
Heater Control

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

The first step when replacing the A/C switch for the rear auxiliary requires separation of the front portion of the overhead console from the headliner. Accomplish the operation by driving the assembly toward the rear while pulling it downward to reveal the retaining tabs. Use a pair of hands to disassemble the auxiliary A/C switch through the rear side tabs until it pushes out from the back. Disconnect the electrical connector. Mix the following steps for installation: connect the electrical connector first then insert the auxiliary A/C switch into the console followed by reinstalling the overhead console onto the headliner.

Begin A/C Switch replacement by unscrewing the console roof screw followed by console removal from headliner. Start by disconnecting the electrical connectors from the console then remove it from the vehicle. Removing the A/C Switch from the console involves pressing in the four tabs found on the switch's back. Begin A/C Switch installation by positioning it on the console then reinsert the electrical connectors into the console. Bind the console to the headliner with an overhead console screw at 2 n.m (18 lb in).

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

To replace HVAC Control Module, from the vehicle initially you will remove instrument panel accessory trim plate and screws that secure the HVAC Control Module. Press out the control assembly retaining tabs to release the HVAC Control Module from the instrument panel, followed by disconnecting the electrical connectors. For installation, attach the electrical connectors to the HVAC Control Module and have the key set at the off position to ensure proper calibration. Next, fit the HVAC Control Module back in the instrument panel with the retaining tabs engaging. Then, attach it using screws and tighten to 1.9 n.m (17 lb in). Finally reinstall the instrument panel accessory trim plate, and run the vehicle for one minute without touching the controls on the HVAC Control Module during calibration calib to prevent improper operation of hvac.

You must firstly extract the instrument cluster trim plate bezel as well as the instrument panel storage tray before you extract the accessory switch assembly from the instrument panel, then finalize the HVAC Control Module replacement. Beginning with the hvac control assembly screws removal you should follow by disengaging retaining tabs to extract the control head from the instrument panel carrier. Separate the electric cables from the hvac control assembly unit. After installing electrical connectors onto the hvac control assembly please keep the key set in off position because this allows proper calibration. Following installation of the hvac control assembly please add the accessory switch assembly and secure it by tightening screws to 1.9 n.m (17 lb in). Install the instrument panel storage tray followed by the instrument cluster trim plate bezel. After starting the vehicle run it for one minute while avoiding any HVAC Control Module adjustments to maintain proper hvac performance.

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

You must take out the console unit first from its seating spot in the headliner. Unsnap the tabs from the back of the overhead console for access to the auxiliary blower motor switch then detach its electrical connector . Reparing the blower motor switch requires connecting the electrical connector first and inserting the switch into the console. Learn how to place the overhead console back on the headliner afterward.

The replacement process for HVAC Control Module begins by uninstalling instrument panel accessory trim and HVAC Control Module mounting screws and retaining tabs. Compressing the holding tabs on the control assembly will free the HVAC Control Module from the instrument panel before disconnecting all attached electrical connectors. Proper calibration requires the key to remain off position when you join electrical connectors to the HVAC Control Module for installation. After placing the HVAC Control Module into the instrument panel slot you must ensure that retaining tabs lock in position before installing screws to tighten at 1.9 n.m (17 lb in). Reinstall the instrument panel accessory trim plate while starting the vehicle to run for one minute with no HVAC Control Module adjustments to prevent inadequate hvac system operation.

You must firstly extract the instrument cluster trim plate bezel as well as the instrument panel storage tray before you extract the accessory switch assembly from the instrument panel, then finalize the HVAC Control Module replacement. Beginning with the hvac control assembly screws removal you should follow by disengaging retaining tabs to extract the control head from the instrument panel carrier. Separate the electric cables from the hvac control assembly unit. After installing electrical connectors onto the hvac control assembly please keep the key set in off position because this allows proper calibration. Following installation of the hvac control assembly please add the accessory switch assembly and secure it by tightening screws to 1.9 n.m (17 lb in). Install the instrument panel storage tray followed by the instrument cluster trim plate bezel. After starting the vehicle run it for one minute while avoiding any HVAC Control Module adjustments to maintain proper hvac performance.

Start HVAC Control Module replacement through these steps: first remove the instrument cluster trim plate bezel and then take out the instrument panel storage tray and finally disconnect the accessory switch assembly from the panel. The hvac control assembly's screws must be removed before pulling the control head out from the instrument panel carrier by releasing its retaining tabs. You must disconnect the electrical cords which connect to the hvac control assembly. Installations require connecting the electrical connectors to the hvac control assembly while the key should maintain an off position to perform proper calibration. Mount the hvac control assembly to the instrument panel followed by the accessory switch assembly while using screws that require tightening to 1.9 n.m (17 lb in). Put back the instrument panel storage tray followed by the instrument cluster trim plate bezel. After starting the vehicle allow it to operate for one full minute with no HVAC Control Module adjustments to ensure optimal hvac functionality.