Make sure this part fits

GM 19213358
Wheel Cylinder, Rear

2005-2008 GM

Customer Questions & Expert Answers (8)
GM 19213358 Wheel Cylinder, Rear
GM 19213358 Wheel Cylinder, Rear
  • Part Description
    Cylinder Assembly, Rear Brake; Wheel Cylinder Repair Kit
  • Position
    Rear
  • Replaces
    10366347
  • Manufacturer
    General Motors
Make sure this part fits
$26.63 MSRP: $50.01
You Save: $23.38 (47%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Vehicle Fitment

    Year Make Model Trim Engine
    2005-2008 Chevrolet CobaltBase, LS, LT, LTZ, Sport, SS4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2006-2008 Chevrolet HHRLS, LS Panel, LT, LT Panel, SS4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2007-2008 Pontiac G5Base, GT4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    2005-2007 Saturn Ion1, 2, 3, Red Line4 Cyl 2.0 L GAS, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is this 19213358 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 19213358 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the wheel cylinder on Chevrolet Cobalt? Posted by Customer
    A:
    In replacing the Wheel Cylinder, first, lift and support the vehicle, then remove the tire and the wheel assembly and then the Brake Drum. Debris and contaminants surrounding the Wheel Cylinder should be removed prior to removing the Wheel Cylinder bleeder cap and valve and brake pipe fitting from the said element, exposing brake pipe end and capping the said end to prevent brake pipe loss and contamination. Next, take off the Wheel Cylinder mounting bolts and using the j 38400 Brake Shoe spanner and spring remover (J 38400), open the top of brake shoes wide enough so as to take off the Wheel Cylinder from the Brake Backing Plate. For installation, use once more the j 38400 to spread the top of the brake shoes apart and place the new Wheel Cylinder into the Brake Backing Plate, and then install the Wheel Cylinder mounting bolts and tighten them to 16 nm (12 ft. Lbs.). On the opposite end of the brake pipe, remove the cap and join the brake pipe fitting at the Wheel Cylinder and screw it full to a torque rating of 19 nm (14 ft. Lb.). Mount the Wheel Cylinder bleeder valve by tightening it to a set of 8 nm (71 inch lbs.), mounting the Brake Drum, bleeding out the hydraulic brake system, and mounting the cap for the bleeder valve. Finally, adjust the drum brakes, mount the tire and wheel assembly, and drop the vehicles.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the wheel cylinder on Chevrolet HHR? Posted by Customer
    A:
    Start the Wheel Cylinder replacement process by raising and supporting your vehicle. Start by extracting the tire with attached wheel followed by the Brake Drum's removal. First clean debris from around the Wheel Cylinder before removing the bleeder cap and valve to disconnect the brake pipe fitting from the Wheel Cylinder. You must cap the exposed brake pipe end to stop fluid loss and protect the brake cylinder from contaminants. Start by removing all mounting bolts which secure the Wheel Cylinder to its position. First use the j 38400 Brake Shoe spanner and spring remover (J 38400) to open the brake shoes at their top ends before extracting the Wheel Cylinder from the Brake Backing Plate. Use the j 38400 tool (J 38400) to open brake shoes at their top while installing the new Wheel Cylinder onto the Brake Backing Plate. Secure the Wheel Cylinder mounting bolts with torque to 16 n.m (12 lb ft). Place the brake pipe end cap aside before fitting the brake pipe connection at the Wheel Cylinder and torquing it to 21 n.m (15 lb ft). Tighten the Wheel Cylinder bleeder valve to 8 n.m (71 lb in) torque. The installation process involves first fitting the Brake Drum followed by bleeding the hydraulic brake system while finishing with bleeder valve cap installation. To finish up follow these steps: adjust the drum brakes and install the tire/wheel assembly before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    Q:
    How do you remove the wheel cylinder from the brake backing plate for the 2007 Chevrolet Cobalt? Posted by Customer
    A:
    Use the Brake Shoe Spanner and Spring Remover (J 38400) to spread the top of the brake shoes apart and remove the wheel cylinder.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Cylinder
    Q:
    What should be done with the brake pipe fitting for the 2006 Chevrolet Cobalt? Posted by Customer
    A:
    Disconnect the brake pipe fitting from the wheel cylinder and cap the exposed brake pipe end to prevent fluid loss and contamination.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Cylinder
    Q:
    What needs to be done to the area around the wheel cylinder for the 2008 Chevrolet Cobalt? Posted by Customer
    A:
    Clean any debris and contaminants from around the wheel cylinder.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Cylinder
    Q:
    What are the final steps after bleeding the hydraulic brake system for the 2006 Chevrolet HHR? Posted by Customer
    A:
    Adjust the drum brakes, then reinstall the tire and wheel assembly before lowering the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Cylinder
    Q:
    What is the first step to replace the wheel cylinder for the 2007 Chevrolet HHR? Posted by Customer
    A:
    Raise and support the vehicle, then remove the tire and wheel assembly followed by the brake drum.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Wheel Cylinder
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Wheel Cylinder, Rear 19213358 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 19213358 Wheel Cylinder, Rear is available in the market under the name GM Wheel Cylinder. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 19213358 Wheel Cylinder, Rear fits certain Chevrolet Cobalt, HHR models, as well as Pontiac G5. Additionally, it is compatible with Saturn Ion models.
The original GM component designated by manufacturer part number 19213358 maintains top performance when functioning as the Cylinder Assembly, Rear Brake; Wheel Cylinder Repair Kit unit at its Rear. The component 19213358 is constructed from durable material and its dimensions span 4.2 x 4.1 x 3.1 inches while weighing 0.70 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Cylinder, Wheel Brake Cylinder/Caliper. The part 19213358 has available replacement options 10366347. Each vehicle needs 2 units of the part marked as SKU 19213358. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.