Make sure this part fits

GM 88957233
CV Joints

2004-2014 GM

Customer Questions & Expert Answers (15)
GM 88957233 CV Joints
  • Part Description
    Outer CV Joint
  • Position
    Front
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2014 Cadillac CTSBase, Luxury, Performance, Premium, V6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
    2004-2009 Cadillac SRXBase6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
    2005-2011 Cadillac STSBase, Platinum, V6 Cyl 3.6 L GAS, 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Is 88957233 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88957233 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How do you remove the CV joint from the wheel drive shaft for the 2009 Cadillac CTS? Posted by Customer
    A:
    With a block of wood and a hammer, remove the CV joint from the wheel drive shaft and discard the retaining clip.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What is the process for engaging the inner race splines for the 2008 Cadillac CTS? Posted by Customer
    A:
    Engage the inner race splines onto the axle shaft splines, compress the axle shaft retaining ring, and drive the outer joint onto the shaft using a wood block and hammer until fully seated.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How do you close the boot clamp for the 2010 Cadillac CTS? Posted by Customer
    A:
    Using the J 42572 - Drive Axle Seal Clamp Pliers, close the boot clamp until the gap measures 1.0 mm (0.040 in).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How do you separate the inboard seal from the trilobal tripot bushing for the 2005 Cadillac SRX? Posted by Customer
    A:
    Slide it away from the joint after separating it.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What tools are needed to replace the front wheel drive shaft outer joint and boot for the 2008 Cadillac SRX? Posted by Customer
    A:
    Drive Shaft Seal Clamp Pliers (J 42572).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How should the large seal retaining clamp be positioned for the 2005 Cadillac STS? Posted by Customer
    A:
    Ensure the inner boot is not dimpled or stretched, and measure the distance between the seal edges to be 88.6 mm (3.50 inch).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How much grease should be applied to the outer joint for the 2006 Cadillac SRX? Posted by Customer
    A:
    Apply approximately 60 percent of the grease from the service kit into the outer joint.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What should be done after locking the boot clamp for the 2010 Cadillac STS? Posted by Customer
    A:
    Remove any excess lubricant from the wheel drive shaft, move the tripot housing assembly to distribute the lubricant in the tripot joint, and reinstall the wheel drive shaft.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How should the outer race be positioned in the bench vise for the 2009 Cadillac SRX? Posted by Customer
    A:
    Wrap a shop towel around the joint outer race splined shaft and place the outer race vertically in a bench vise.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What is the first step to replace the Front Wheel Drive Shaft Outer Joint and Boot for the 2010 Cadillac STS? Posted by Customer
    A:
    Ensure the wheel drive shaft is removed from the vehicle.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How much grease should be inserted into the inner joint during assembly for the 2007 Cadillac SRX? Posted by Customer
    A:
    Approximately 60 percent of the grease from the service kit.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What should be done to the wheel drive shaft inboard seal before repacking for the 2007 Cadillac STS? Posted by Customer
    A:
    Grease the wheel drive shaft inboard seal and repack the housing.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    How do you crimp the small seal retaining clamp for the 2008 Cadillac STS? Posted by Customer
    A:
    Use the Drive Shaft Seal Clamp Pliers (J 42572), ensuring a gap of 1 mm (0.039 in) at the base of the omega ohm shape.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    Q:
    What should be done to distribute grease throughout the tripot spider bearings for the 2006 Cadillac STS? Posted by Customer
    A:
    Rotate the inner tripot housing 4 or 5 times.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar CV Joint
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM CV Joints 88957233 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88957233 CV Joints is available in the market under the name GM CV Joint. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88957233 CV Joints fits certain Cadillac CTS, SRX, STS models.
The original GM component designated by manufacturer part number 88957233 maintains top performance when functioning as the Outer CV Joint unit at its Front. The component 88957233 is constructed from durable material and its dimensions span 25.1 x 5.8 x 5.8 inches while weighing 6.60 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Outer Joint Assembly; Joint Kit, Front Wheel Drive Axle; CV Joint. The part 88957233 has available replacement options. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.