Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 15912466
Latch, Driver Side

1994-2004 GM

Customer Questions & Expert Answers (9)
GM 15912466 Latch, Driver Side
GM 15912466 Latch, Driver Side
GM 15912466 Latch, Driver Side
  • Part Description
    Latch, End Gate Lock; Trunk Latch; Door Lock
  • Position
    Driver Side
  • Replaces
    15726085
  • Manufacturer
    General Motors
Make sure this part fits
$48.26 MSRP: $69.65
You Save: $21.39 (31%)
1
ADD TO CART

  • 15912466 Latch, Driver Side is Ref No. 7 in the diagram below

    2001 Chevy S10 Latch, Driver Side Diagram for 15912466
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 15912466

  • Vehicle Fitment

    Year Make Model Trim Engine
    1994-2004 Chevrolet S10Base, LS, SS, Xtreme, ZR2, ZR54 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
    1994-2004 GMC SonomaSL, SLE, SLS4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 6 Cyl 4.3 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is this 15912466 designed for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 15912466 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace a Tailgate Latch on an End Gate on Chevrolet S10? Posted by Customer
    A:
    Begin replacing the tailgate latch by using these sequential steps. Start by opening the tailgate and taking off the tailgate trim panel. The procedure starts with removing the tailgate latch rod from the tailgate latch followed by unbolting the tailgate latch from tailgate installation. When the latch is free from the vehicle you may remove it. Before beginning installation place the new tailgate latch inside the vehicle while paying attention to the Fastener Notice guidelines for service safety procedures. After bolting the tailgate latch to the tailgate you must tighten them to a torque of 10 N.m (88 lb in) before replacing the tailgate latch rod to the tailgate latch and reinstalling the tailgate trim panel.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Remove and Replace a Rear Door Lock Actuator on GMC Sonoma? Posted by Customer
    A:
    Return of the rear door power Door Lock Actuator requires beginning the installation by removing door trim panel followed by the water deflector and the Door Latch Assembly. The lock actuator gets secured against the latch through two screws which need removal. Rotate the actuator upward and backward until the rubber Bumper detachment occurs from the latch before taking out the actuator. Begin the installation by connecting the rubber Bumper to the latch and move the actuator next to the rubber Bumper until completion of engagement. The proper functionality of the system depends on correct tooth alignment between the actuator gear and the latch gear starting point. Position the actuator on top of the latch before installing the 2 screws which will secure the actuator to the latch by torquing them to 0.75 n.m (6 lb in). Finish by installing the latch onto the door after which you should replace the water deflector followed by the door trim panel.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Replace a Tailgate Latch on an End Gate Window on GMC Sonoma? Posted by Customer
    A:
    Begin by taking off the endgate cover and marking the latch location for accurate alignment when installing a new endgate window latch. Unplug electrical connectors before you remove nuts connecting the endgate window latch to support its bracket. Then pull off the latch from the endgate. Place the new endgate window latch based on the earlier alignment marks then install its retaining nuts by torqueing them to 10 N.m (88 lb in). After installation, restore electrical connections where needed and place back the endgate cover.
    Posted by ChevyPartsGiant Specialist
    Q:
    What is the first step in the installation process for the 2002 Chevrolet S10? Posted by Customer
    A:
    Attach the rubber bumper to the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    How should the actuator be positioned during installation for the 2003 Chevrolet S10? Posted by Customer
    A:
    Rotate the actuator toward the latch to ensure the rubber bumper is fully engaged.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What should be removed after the door trim panel for the 2002 Chevrolet S10? Posted by Customer
    A:
    Remove the water deflector and the door latch assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is crucial to align during the installation for the 2004 GMC Sonoma? Posted by Customer
    A:
    Align and interlock the first tooth of the gear on the actuator with the first tooth of the gear on the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    Q:
    What is the first step in the installation process for the 2003 GMC Sonoma? Posted by Customer
    A:
    Attach the rubber bumper to the latch.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Door Lock Actuator
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Latch, Driver Side 15912466 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 15912466 Latch, Driver Side is available in the market under the name GM Door Lock, Door Lock Actuator, Tailgate Latch, Tailgate Lock, Trunk Latch. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 15912466 Latch, Driver Side fits certain Chevrolet S10 models, as well as GMC Sonoma models.
The original GM component designated by manufacturer part number 15912466 maintains top performance when functioning as the Latch, End Gate Lock; Trunk Latch; Door Lock unit at its Driver Side. The component 15912466 is constructed from durable material and its dimensions span 4.3 x 4.5 x 15.0 inches while weighing 1.30 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 15912466 has available replacement options 15726085. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.