Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

GM 88964580
Turn Signal Switch

2000-2005 GM

Customer Questions & Expert Answers (12)
GM 88964580 Turn Signal Switch
GM 88964580 Turn Signal Switch
GM 88964580 Turn Signal Switch
GM 88964580 Turn Signal Switch
GM 88964580 Turn Signal Switch
GM 88964580 Turn Signal Switch
  • Part Description
    Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Combination Switch
  • Replaces
    26093873, 26073612, 26085930
  • Manufacturer
    General Motors
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 88964580 Turn Signal Switch is Ref No. 6 in the diagram below

    2001 Chevy Impala Turn Signal Switch Diagram for 88964580
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 88964580

  • Vehicle Fitment

    Year Make Model Trim Engine
    2000-2005 Chevrolet ImpalaBase, LS, LS Sport, SS6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    2000-2005 Chevrolet Monte CarloLS, LS Competition, LS Sport, LT, SS, SS 35th Anniversary Edition, SS Dale Earnhardt Signature Edition, SS High Sport, SS Pace Car6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Is 88964580 compatible with my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 88964580 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Headlight Switch on Chevrolet Impala? Posted by Customer
    A:
    The replacement of the headlamp switch starts with removing the instrument panel cluster trim plate bezel then continuing to the screws from the headlamp switch housing. Following this step disconnect the foglamp switch along with the headlamp switch from the instrument panel by removing the headlamp switch housing. A flat-bladed tool must be utilized to extract the foglamp switch from its housing with the headlamp switch. Press the foglamp switch into place within the headlamp switch housing until it reaches complete seating position. Join the electrical cables that will link the headlamp switch and foglamp switch. Attach the headlamp housing switch back to the instrument panel while securing it with screws which should be tightened to 2 N.m (18 lb in). You should reinstall the instrument panel cluster trim plate bezel as the last step.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to Service and Repair the Headlight Switch on Chevrolet Impala? Posted by Customer
    A:
    The replacement of the headlamp switch starts with removing the instrument panel cluster trim plate bezel followed by unfastening the screws on the headlamp switch housing. Disconnect both the electical connectors which service the headlamp switch and foglamp switch after pulling out the headlamp switch housing from its assignment in the instrument panel. A flat bladed tool can be used to detach the foglamp switch from its position inside the headlamp switch housing. To mount the foglamp switch start with pressing it so it becomes completely seated within the headlamp switch housing. Connect the electrical wiring to each of the headlamp switch and foglamp switch devices. Secure the headlamp housing switch at the instrument panel using screws that should be tightened to 2 N.m (18 lb in). The last part of the repair includes reinstallation of the instrument panel cluster trim plate bezel.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Turn Signal Switch on Chevrolet Monte Carlo? Posted by Customer
    A:
    Start by disabling the SIR system as explained in the Service Precautions section before replacing the multifunction turn signal lever of the vehicle. Detach the wire harness assembly from its mounting strap while taking note of its connector outlet in the abrasion sleeve. Unplug the turn signal and multifunction switch assembly at both ends from the SIR system coil connector and let its 2 endcaps fall out of the grounded housing. Take off both pan head tapping screws from the turn signal/multifunction switch and pull the assembly out of the steering column tilt head. Fasten the turn signal and multifunction switch assembly onto the steering column tilt head assembly with the provided 2 pan head tapping screws . Tighten the top screw to 3 N.m (30 lb in) and the side screw to 7 N.m (62 lb in). Push both ends of the turn signal and multifunction switch assembly connectors into the bulkhead interface then link the switch assembly to the SIR coil connector. Place the wire harness assembly back into its strap after making sure the abrasion sleeve fits correctly on the steering column harness. Let the ignition lock cylinder case wires and electrical connector extend through the middle opening. Reapply both trim sections and activate the SIR system.
    Posted by ChevyPartsGiant Specialist
    Q:
    How to replace the Headlight Switch on Chevrolet Monte Carlo? Posted by Customer
    A:
    Start by taking out the instrument panel cluster trim plate bezel after which you can remove the screws from the headlamp switch housing. The first step is to remove the headlamp switch housing from the instrument panel before disconnecting the electric wiring from both the headlamp switch and foglamp switch. A flat blade tool should be used to detach the foglamp switch from within the headlamp switch housing. Start the foglamp installation by pushing the switch through the headlamp switch housing until it achieves total seating. After you have installed the foglamp switch into the headlamp switch housing you should join the electrical connectors to the headlamp switch and the foglamp switch. Install the headlamp housing switch back to the instrument panel while following the Fastener Notice that requires screw tightness at 2 N.m (18 lb in). The final step of the procedure includes putting back the instrument panel cluster trim plate bezel.
    Posted by ChevyPartsGiant Specialist
    Q:
    What should be done after removing the screws for the 2002 Chevrolet Impala? Posted by Customer
    A:
    Take the headlamp switch housing out of the instrument panel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Headlight Switch
    Q:
    What should be done after positioning the lever for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Install the retaining bolts, tightening them to 7 Nm (62 inch lbs.), and connect the gray and black connectors.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Turn Signal Switch
    Q:
    What is the next step after removing the trim covers for the 2005 Chevrolet Monte Carlo? Posted by Customer
    A:
    Detach the wire harness assembly from the wire harness strap and disconnect the turn signal and multifunction switch assembly connector from the SIR system coil connector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Turn Signal Switch
    Q:
    What are the final steps after reconnecting the connectors for the 2002 Chevrolet Monte Carlo? Posted by Customer
    A:
    Reattach the steering column bulkhead connector to the vehicle wire harness, install the two wire harness straps, and secure the steering column wire harness to the retainer.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Turn Signal Switch
    Q:
    How should the assembly be secured for the 2004 Chevrolet Impala? Posted by Customer
    A:
    Secure the assembly with the two pan head tapping screws, tightening the top screw to 3 Nm (27 in. lbs.) and the side screw to 7 Nm (62 in. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Turn Signal Switch
    Q:
    What is the first step to service the headlamp switch for the 2000 Chevrolet Monte Carlo? Posted by Customer
    A:
    Remove the instrument panel cluster trim plate bezel.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Headlight Switch
    Q:
    What needs to be disconnected from the wire harness for the 2001 Chevrolet Impala? Posted by Customer
    A:
    Disconnect the steering column bulkhead connector and the connectors from the multifunction turn signal lever steering column bulkhead connector.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Turn Signal Switch
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Turn Signal Switch 88964580 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 88964580 Turn Signal Switch is available in the market under the name GM Dimmer Switch, Headlight Switch, Turn Signal Switch, Wiper Switch. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 88964580 Turn Signal Switch fits certain Chevrolet Impala, Monte Carlo models.
The original GM component designated by manufacturer part number 88964580 maintains top performance when functioning as the Switch Assembly, Turn Signal & Headlamp Dimmer, Wiper & Washer (W/Lever); Multi Purpose Combination Switch unit. The component 88964580 is constructed from durable material and its dimensions span 11.1 x 6.4 x 6.4 inches while weighing 1.40 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. This component receives the designation of Turn/Wiper Lever; Switch, Windshield Wiper Control; Switch, Turn Signal Lamp; Switch, Headlamp Dimmer. The part 88964580 has available replacement options 26093873, 26073612, 26085930. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.