Question 1

How to replace the Release Hood Cable on Buick LaCrosse?

Accepted Answer

Start the replacement of Hood Cable by first opening the hood then removing the left front headlamp. The Hood Latch should stay blocked while the new cable installation takes place. Detach the Hood Cable from the latch mechanism before proceeding to remove the front fender upper diagonal brace together with the air cleaner. A wire or string must be attached to the Hood Cable end in order to help with installation while keeping it within the engine compartment. You should detach the Hood Cable retainers at the engine compartment side rail then pull back the carpet to reach the cable before removing the Hood Cable handle and its respective cable. The removal requires a flat small tool to separate the dash panel grommet before proceeding to extract the Hood Cable from the dash panel. To install the Hood Cable users must tie a string or wire to it before pulling it to the grommet opening in the dashboard panel where they should apply strip caulk sealer to the grommet. Install the hood handle after connecting the cable to it. After pulling back the carpet a second time you should fasten each Hood Cable retainer to the side rail of the engine compartment. The cable needs to run under the radiator support before putting back the air cleaner and front fender upper diagonal brace while hooking up the Hood Cable to its designated latch position. As the concluding step reinstall both the left front headlamp while removing the block from the Hood Latch then verify the latch functions correctly before you close the hood.

Question 2

How to Install a New Hood Cable on Buick LeSabre?

Accepted Answer

Opening the hood requires the first step for replacing the Hood Cable. After that, remove the Hood Latch to continue. A string thread around the Hood Cable will assist with its insertion into the engine compartment before you remove the front fascia extension and front wheelhouse liner. The Hood Cable should have three clips opened when you maintain cable connection to your vehicle before taking out the handle attaching screws. Leverage two pieces of string to detach the Hood Cable from the hood release handle before putting the cable through the passenger compartment. Lift out the Hood Cable grommet from the wheel opening to remove the Hood Cable from the automobile. Transfer the string to different ends of the new Hood Cable before installing the cable through the passenger compartment and remove the string. Tie the Hood Cable to the hood release handle with the two fasteners installed. When installing the Hood Cable grommet into the wheel opening first push the grommet into position before pulling the cable and the string to the engine compartment and once more removing the string. After inserting the Hood Cable into its clips, close the clips and reinstall the front wheelhouse liner, front fascia extension and Hood Latch before you close the hood.

Question 3

How to replace the Hood Cable on Buick Regal?

Accepted Answer

The first step to replace hood primary cable includes opening the hood followed by left front headlamp removal. Use a block on the Hood Latch to maintain an unlocked position while you install the new cable. Start by disconnecting the Hood Cable from the latch mechanism before removing front fender upper diagonal brace. Succeeding steps call for satisfying 3.1l or 3.8l specific air cleaner extraction protocols. For new cable installation ease you may tie a wire to the end of your old Hood Cable then secure it inside the engine compartment. Pull back the carpet to reach the cable when you remove the Hood Cable retainers from the engine compartment side rail. Start by removing the hood release handle then detaching its cable from the assembly. Next, use a small flat-bladed tool to remove the grommet from the dash panel which allows access to the tied cable. To install the new Hood Cable, first feed the wire or string with the cable installed through the dash panel grommet before applying strip caulk sealer at the grommet. Install the hood release handle while connecting the cable to its position. Start by pulling back the carpet and you should secure the Hood Cable retainers to the engine compartment side rail. Refollow engine guidelines to reinstall the air cleaner after routing the cable through the radiator support. Proceed with reinserting the front fender upper diagonal brace then link the Hood Cable to the Hood Latch before installing the left front headlamp. The ending operation involves taking out the blocking piece from the Hood Latch before completing hood closure.

OEM Buick Hood Cable

54 Hood Cables found

Buick Release Cable

Buick Release Cable

Buick Release Cable

Buick Release Handle, Jet Black

Buick Release Cable

Buick Release Cable

Buick Lock Cable

Buick Release Cable

Buick Release Cable

Buick Release Cable

Buick Release Cable

Buick Release Cable, Black

Buick Release Cable

Buick Release Cable

Buick Release Cable

Buick Release Cable

Buick Handle

Buick Release Cable

Buick Release Handle

Buick Release Cable

Buick Hood Cable Parts Questions & Experts Answers

Related Buick Parts

Browse Buick Hood Cable by Models