GM 15242999
Release Cable

Begin by opening the hood and taking out the Hood Latch before you detach the Hood Cable from its link with the Hood Latch. The installation process should start with stringing the Hood Cable and then removing the front fascia extension followed by the front wheelhouse liner from the vehicle. Use the tools to access the Hood Cable retaining clips which connect to the vehicle before uninstalling the screws holding the hood release handle and disconnecting the cable from the handle. Use thread to make handling the Hood Cable easier and remove its grommet from the wheel opening before removing the Hood Cable out of the vehicle. To install the Hood Cable begin by moving the attached string to each end of the new cable. You should then direct the cable through the passenger compartment before taking out the string once more. The Hood Cable must be linked with the hood release handle while the fasteners secure its junction. Since the Hood Cable grommet fits into the wheel opening, insert it by using a press and release motion. Then pull the Hood Cable inside the engine compartment alongside the string. Finally remove the string from the engine compartment. After placing the Hood Cable into its position you can close the clips before reinstalling the front wheelhouse liner, front fascia extension and Hood Latch. Finally close the hood.

Opening the hood requires the first step for replacing the Hood Cable. After that, remove the Hood Latch to continue. A string thread around the Hood Cable will assist with its insertion into the engine compartment before you remove the front fascia extension and front wheelhouse liner. The Hood Cable should have three clips opened when you maintain cable connection to your vehicle before taking out the handle attaching screws. Leverage two pieces of string to detach the Hood Cable from the hood release handle before putting the cable through the passenger compartment. Lift out the Hood Cable grommet from the wheel opening to remove the Hood Cable from the automobile. Transfer the string to different ends of the new Hood Cable before installing the cable through the passenger compartment and remove the string. Tie the Hood Cable to the hood release handle with the two fasteners installed. When installing the Hood Cable grommet into the wheel opening first push the grommet into position before pulling the cable and the string to the engine compartment and once more removing the string. After inserting the Hood Cable into its clips, close the clips and reinstall the front wheelhouse liner, front fascia extension and Hood Latch before you close the hood.

The first step to replace the Hood Cable begins with opening the hood before removing the Hood Latch. The hood release cable needs disconnection from both the Hood Latch and from the hood release handle. Secure a string around the hood release cable early to aid installation through the passenger area and afterward remove the hood release grommet from the dash while recording the cable path before taking out the cable from the car. The string should be placed at both ends of the new hood release cable before guiding the cables into the passenger compartment and eliminating the string. Position the hood release cable grommet into the cowl opening as you install the hood release cable to the hood release handle after which you can pull both string and cable into the engine bay through the cowl space then remove the string. The hood release cable should be installed onto the Hood Latch. After reinstalling the Hood Latch you should close the hood.

The replacement of the Hood Cable requires one to first unlatch the hood before starting the work. First step to replacing the Hood Cable consists of removing it from the Hood Latch then applying string for easier handling during installation through the engine bay. You must start by taking off the front wheelhouse liner after which you should open the launch clips which maintain the Hood Cable and then remove the screws that attach the hood release handle to the vehicle structure. The Hood Cable needs disconnecting from its handle using string to link it so installation becomes simpler in the passenger area. Pull out both the Hood Cable grommet from the wheel opening along with the cable itself from inside the vehicle. Pass the string ends correctly to each Hood Cable terminus before guiding the strings through the passenger space until the string comes out. Install the grommet into its wheel opening before you join the cable to the hood release handle and fasten the handle in place. First pull the string with cable into the engine compartment after removing the string once more to properly place the cable into the clips which you will secure with the clips. After completing the installation by putting the front wheelhouse liner into place and then installing the Hood Latch as well as securing the hood.

The replacement process of Hood Cable starts with opening the hood followed by removing the upper filler panel. The initial step requires removing the Hood Latch followed by separating the Hood Cable from the Hood Latch. A string should be wrapped around the Hood Cable before putting it through the engine compartment. The first step is to discard the front wheelhouse liner and then uncover the clips which restrain the Hood Cable to the vehicle body. Take off the fasteners attaching the hood release handle and free up the cable from the handle. Attach another string to the Hood Cable to help threading it through the passenger area afterward. Remove the Hood Cable grommet from the wheel opening and take out the cable itself. To integrate the new cable install the string ends through the passenger compartment while removing the string afterward. You should place the grommet into the wheel opening after connecting the Hood Cable to the hood release handle by securing it with fasteners. Proceed with correcting the cable by pulling the string and cable through the engine compartment then removing the string before positioning the cable into the clips then closing the clips. You must reinstall the front wheelhouse liner with the Hood Latch and upper filler panel until you close the hood.

Start the replacement process of the hood primary latch cable by opening the hood then removing the Hood Latch. Secure a string around the Hood Cable for easier installation through the engine compartment. The front wheelhouse panel should be taken off followed by opening the three clips securing the Hood Cable to the car. Remove the two fasteners holding the hood handle to the vehicle then disconnect the Hood Cable from the handle. You need to tie a piece of string to the Hood Cable for installation through the passenger area before removing the Hood Cable grommet from the wheel opening and taking out the cable from the vehicle. Direct the string to both ends of the Hood Cable before leading them into the passenger compartment for installation. To install the Hood Cable begin by removing the string and attaching the cable to the hood handle. Secure the handle using both fasteners. Press the headlight hood grommet into the wheel opening while positioning it properly. Afterward pull the string and Hood Cable into the engine area then remove the string completely. Close the clips on the Hood Cable followed by reinstalling both the front wheel panel and Hood Latch before you can properly shut the hood.

Transfer the string to either end of the new hood release cable, route it into the passenger compartment, and remove the string.

Transfer the string to either end of the new hood release cable and route it into the passenger compartment, then remove the string.

Remove the hood release cable grommet from the dash panel, noting the cable's routing before removing it from the vehicle.

Note the cable's routing before removing it from the vehicle.

Pull the string and the hood release cable into the engine compartment, remove the string again, install the hood release cable to the hood latch, install the hood latch, and close the hood.

Install the hood release cable to the hood latch, reinstall the hood latch, and close the hood.

Position the hood release cable in the clips, close the clips, install the front wheelhouse liner, and the hood latch before finally closing the hood.

Pull the string and cable into the engine compartment, remove the string again, position the cable in the clips, close the clips, and finally install the front wheelhouse liner and the hood latch before closing the hood.

Seat the hood release cable grommet into the wheel opening and connect the hood release cable to the hood release handle.

Reinstall the front wheelhouse liner, the hood latch, and the upper filler panel before closing the hood.

Tie another piece of string around the hood release cable.

Disconnect the hood release cable from the hood release handle and tie another piece of string around the cable.

Remove the hood release cable grommet from the wheel opening and take out the hood release cable from the vehicle.

Open the hood and remove the upper filler panel.