Make sure this part fits

GM 25983762
Caliper, Driver Side

2006-2016 GM

Customer Questions & Expert Answers (13)
GM 25983762 Caliper, Driver Side
  • Part Description
    Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
  • Position
    Driver Side
  • Replaces
    21993094
  • Manufacturer
    General Motors
Make sure this part fits
$121.31 MSRP: $217.61
You Save: $96.30 (45%)
Currently Unavailable

Due to manufacturer supply shortage, this item isn't currently available for ordering.

  • Vehicle Fitment

    Year Make Model Trim Engine
    2008-2009 Buick LaCrosseSuper8 Cyl 5.3 L GAS
    2006-2011 Buick LucerneCXL, CXS, Super8 Cyl 4.6 L GAS
    2006-2011 Cadillac DTSBase, Livery, Luxury, Platinum, Premium8 Cyl 4.6 L GAS
    2006-2013 Chevrolet ImpalaPolice6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
    2014-2016 Chevrolet Impala LimitedPolice6 Cyl 3.6 L FLEX
    Warning: California's Proposition 65
  • Customer Questions & Expert Answers

    Q:
    Can you help me check if this 25983762 is the right part for my car? Posted by ChevyPartsGiant Specialist
    A:
    Please Select Your Vehicle model to see if part number 25983762 is suitable before ordering.
    Posted by ChevyPartsGiant Specialist
    Q:
    How do you disconnect the park brake cable for the 2008 Buick LaCrosse? Posted by Customer
    A:
    Release the park brake cable tension at the equalizer, disconnect the front and rear cables at the connector clip, and detach the park brake cable from the park brake lever on the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the integral park brake mechanism be inspected for the 2006 Buick Lucerne? Posted by Customer
    A:
    Rotate the park brake lever without disassembling it, as the lever, return spring, and actuator shaft seal are non-serviceable.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How should the brake caliper assembly be cleaned for the 2006 Buick Lucerne? Posted by Customer
    A:
    Clean the brake caliper assembly with denatured alcohol and dry it with filtered, lubricated compressed air.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you seat the caliper pistons and pads for the 2010 Cadillac DTS? Posted by Customer
    A:
    With the engine off, gradually apply the brake pedal to about 2/3 of its travel, slowly release it, and repeat until a firm pedal is achieved.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you compress the caliper pistons for the 2007 Cadillac DTS? Posted by Customer
    A:
    Use a large C-clamp over the brake caliper body, tightening it until the caliper pistons are compressed enough to slide past the brake rotor.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    How do you remove the brake caliper for the 2009 Cadillac DTS? Posted by Customer
    A:
    Remove the brake caliper pin bolts and take off the brake caliper.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after inspecting the fluid level for the 2008 Cadillac DTS? Posted by Customer
    A:
    Raise and support the vehicle, then mark the relationship of the wheel to the axle flange and remove the tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done if the fluid level is higher than midway for the 2006 Cadillac DTS? Posted by Customer
    A:
    Reduce it to the midway point.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What is the torque specification for the caliper bolts for the 2006 Chevrolet Impala? Posted by Customer
    A:
    Tighten them to 44 Nm (32 ft. lbs.).
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be done after inspecting the fluid level for the 2007 Chevrolet Impala? Posted by Customer
    A:
    Raise and support the vehicle, then remove the rear tire and wheel assembly.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What should be inspected on the caliper bracket for the 2008 Chevrolet Impala? Posted by Customer
    A:
    Inspect the caliper bracket bolt boots for cuts, tears, or deterioration, replacing any damaged boots. Check the caliper bolts for corrosion or damage, using new bolts and bushings if necessary.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    Q:
    What lubrication is required during installation for the 2009 Chevrolet Impala? Posted by Customer
    A:
    Lubricate the caliper bolts (1 and 3) with silicone grease, avoiding the threads, and lubricate the 2 bolt boots (13 and 4) in the caliper bracket with silicone grease.
    Posted by ChevyPartsGiant Specialist
    See expert answers on similar Brake Calipers
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM GM Caliper, Driver Side 25983762 Designed for Proper Fit and Performance

Original OEM GM parts deliver superior quality and meet all performance standards needed for optimal automotive operation. The authentic part identified by 25983762 Caliper, Driver Side is available in the market under the name GM Brake Calipers. This genuine product has a full warranty coverage from the manufacturer available at all authorized GM dealers throughout the United States. This part 25983762 Caliper, Driver Side fits certain Chevrolet Impala, Impala Limited models, as well as Cadillac DTS. Additionally, it is compatible with Buick LaCrosse, Lucerne models.
The original GM component designated by manufacturer part number 25983762 maintains top performance when functioning as the Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper unit at its Driver Side. The component 25983762 is constructed from durable material and its dimensions span 7.4 x 5.2 x 10.2 inches while weighing 9.70 Pounds. The Direct Replacement component is ready in New condition to ensure full compatibility with your vehicle system. The part 25983762 has available replacement options 21993094. GM manufacturer provides a warranty that ensures reliable operation of this product. The Shipping Policy and Return Policy pages outline complete details regarding shipping procedures and return processes.
If you want to save money in the long run on maintenance and repairs, you should choose OEM products because they're of the top level of durability. Are you on the quest of finding GM parts, our site is worth a visit. We stock an endless selection of high-quality GM components including things like ignition coils all the way through to fan shrouds and all at prices that can not be matched. You have nothing to worry about because all our OEM parts are covered with a manufacturer warranty, which guarantees superior quality and value.