GM 15716364
Splash Shield

After freeing the park brake you need to lift the vehicle and place supports under it to proceed with the replacement. Take off the tire and wheel unit before easing the park brake cable tension by pulling down on the cable near the equalizer bar and then detaching it from the equalizer. Take off the park brake cable from its mounting bracket using the locking tabs and remove the rear brake cable end from the park brake actuator lever . First unfasten the rotor from the housing then lower the Axle Shaft before taking out the park brake shoe. Using a socket and wrench remove the backing plate bolts until you can take the backing plate away from the axle housing flange. Put the backing plate on the axle housing flange first then use the backing plate nuts to fasten it at 135 nm (100 ft. Lbs.). Install the park brake shoe first and then the Axle Shaft before adjusting the park brake shoe. Install the rotor while connecting the rear park brake cable end back to the park brake actuator lever and fasten the park brake cable to its mounting bracket through the locking tabs. Complete the installation by connecting the equalizer bar to the park brake cable then put back the tire and wheel unit. Take out the safety stands and lower the vehicle while setting the park brake properly.

In order to remove the front disc Brake Dust Shields, you have to first jack up and support the vehicle, and the tire and wheel assembly. After that, go and remove which is hubbard and bearing assembly, then remove dust shields (15 Series) and dust shields (25 Series). For installation, the first installation is by installing the dust shield (25 Series), followed by dust shield (15 Series), then the hub and bearing assembly. Then, reinstall the tire and wheel assembly, remove safety stands, and lower the vehicle. Make sure that one watches out for precautions in terms of brake dust in the process.

In order to remove the front disc Brake Dust Shields, you have to first jack up and support the vehicle, and the tire and wheel assembly. After that, go and remove which is hubbard and bearing assembly, then remove dust shields (15 Series) and dust shields (25 Series). For installation, the first installation is by installing the dust shield (25 Series), followed by dust shield (15 Series), then the hub and bearing assembly. Then, reinstall the tire and wheel assembly, remove safety stands, and lower the vehicle. Make sure that one watches out for precautions in terms of brake dust in the process.

After freeing the park brake you need to lift the vehicle and place supports under it to proceed with the replacement. Take off the tire and wheel unit before easing the park brake cable tension by pulling down on the cable near the equalizer bar and then detaching it from the equalizer. Take off the park brake cable from its mounting bracket using the locking tabs and remove the rear brake cable end from the park brake actuator lever . First unfasten the rotor from the housing then lower the Axle Shaft before taking out the park brake shoe. Using a socket and wrench remove the backing plate bolts until you can take the backing plate away from the axle housing flange. Put the backing plate on the axle housing flange first then use the backing plate nuts to fasten it at 135 nm (100 ft. Lbs.). Install the park brake shoe first and then the Axle Shaft before adjusting the park brake shoe. Install the rotor while connecting the rear park brake cable end back to the park brake actuator lever and fasten the park brake cable to its mounting bracket through the locking tabs. Complete the installation by connecting the equalizer bar to the park brake cable then put back the tire and wheel unit. Take out the safety stands and lower the vehicle while setting the park brake properly.

In order to remove the front disc Brake Dust Shields, you have to first jack up and support the vehicle, and the tire and wheel assembly. After that, go and remove which is hubbard and bearing assembly, then remove dust shields (15 Series) and dust shields (25 Series). For installation, the first installation is by installing the dust shield (25 Series), followed by dust shield (15 Series), then the hub and bearing assembly. Then, reinstall the tire and wheel assembly, remove safety stands, and lower the vehicle. Make sure that one watches out for precautions in terms of brake dust in the process.

Begin replacing the front Brake Dust Shields on 1500 series by taking out its hub and bearing parts first. Place the splash shield first and then put on the hub and bearing components. Keep the brake dust caution in mind when doing this work.

Begin by following the specific procedures to remove the park brake cable either from the left or right side before beginning the drum Brake Backing Plate replacement. After disconnecting the Wheel Cylinder and rear Axle Shaft and backing plate bolts the technician can remove the backing plate. Following these steps install the backing plate by placing it on the rear axle housing then bolt it into position before torquing the bolts to 135 nm (100 ft. Lbs.). Finish the repair by reinstalling the rear Axle Shaft followed by the Wheel Cylinder and ending with the appropriate installation procedure for the park brake cable.

The front disc brake dust shield replacement for the 1500 series begins with removing the hub and bearing assembly and ending with dust shield removal. Start with installing the dust shield and returning the hub and bearing assembly to place. Anti-brake dust caution rules must be followed during the process.

Start the backing plate replacement by loosening the parking brake and elevating the vehicle. Take the tire off and remove the wheel unit before taking the caliper with its mounting bracket as one piece. Release park brake cable tension by unscrewing the equalizer nut and separate the cable from the lever and bracket through its locking tabs. Remove both the rotor and Axle Shaft before proceeding to take out the Parking Brake Shoe. Disassemble the backing plate bolts and pull off the backing plate from the axle housing flange. After preparing the threads with brake parts cleaner apply threadlock gm p/n 12345493 or red loctite (TM) #272 product and fasten the new backing plate to the axle housing flange with proper torque of 135 n.m (100 lb ft). Fit back the Parking Brake Shoe and set it to required position. Put on the Axle Shaft and rotor then attach the park brake cable back to its mounting bracket and lever. Tighten the equalizing nut to 3.5 nm (31 lb in) when complete. Completing the process means you reinstall the caliper along its mount while placing back the tire and wheel combo then take safety stands off and lower down your vehicle while readjusting the park brake cable.

Replacement of the rear Brake Backing Plate requires initial park brake cable removal according to the processes mentioned in parking brake front cable replacement for the left cable and parking brake rear cable replacement - left side (w/Rear Disc) and parking brake rear cable replacement - left side (w/Rear Drum) for the right cable. The brake procedure begins by taking out the Wheel Cylinder followed by removing the rear Axle Shaft and concluding by unfastening the backing plate bolts to extract the backing plate. The backing plate gets installed onto the rear axle housing by following service precaution fastener notice instructions before installing backing plate bolts which must be tightened to 135 nm (100 ft. Lbs.). Reinstall the rear Axle Shaft followed by the Wheel Cylinder and the park brake cable. All installations must follow operations documented for the left and right cables.

To replace the disc Brake Dust Shields, initially ask to lift and support the vehicle with proper lifting means. Next take away the tire and wheel assembly and then followed by the hub and bearing assembly. After that, remove the dust shields (15 series) and spill shield (25 series). For installation, start by installing dust shields (15 series), follow it with the dust shield (25 series). Following that, reinstall hub and bearing assembly as well as tire and wheel assembly. Lastly, take away the safety stands and lower the vehicle.

In order to remove the front disc Brake Dust Shields, you have to first jack up and support the vehicle, and the tire and wheel assembly. After that, go and remove which is hubbard and bearing assembly, then remove dust shields (15 Series) and dust shields (25 Series). For installation, the first installation is by installing the dust shield (25 Series), followed by dust shield (15 Series), then the hub and bearing assembly. Then, reinstall the tire and wheel assembly, remove safety stands, and lower the vehicle. Make sure that one watches out for precautions in terms of brake dust in the process.

Secondly as part of replacing the rear disc Brake Backing Plate for the 25/35 series and the 2500 series, release the park brake, and lift up and support vehicle. Take off the tire and wheel assembly, and then remove the tension in the park brake cables by loosening the nut on the equalizer face. Pull off the rear cable of the park brakes from the lever of the park brake actuator and disengage it from the bracket that holds the mounting bracket by the use of locking tabs. In its turn, detai, axle shaft, and park brake shoe, and backing plate on the next toti, nuts from the backing plate to remove the backing plate to the axle house i came. For the installation, you need to attach backing plate to the axel housing flange and tighten the backing plate with nuts to 135 nm (100 ft. Lbs.). Reinstall the park brake shoe and Axle Shaft, adjusting it. Mount the rotor and reconnect the park brake cable to the bracket and ensure the locking tabs lock in place. Reattach the rear park brake cable to the park brake actuator lever and tighten the nut to the equalizer to 3.5 nm (31 inch lbs). Lastly, secure the tire and wheel assembly back, remove the safety stands, lower the vehicle and adjust the park brake cable.

To fix the rear disc Brake Backing Plate in 15 series w/nys vehicles start by unlocking the parking brake and lifting the vehicle with assistance. Take off the wheel assembly before loosening park brake tension by pulling down on the middle cable until it frees from the equalizer bar. First disconnect the rear park brake bracket bolt and separate the park brake cable from the park brake actuator lever. After that remove the Wheel Bearing. You should take out the backing plate, actuator lever housing and park brake shoe from their locations in turn. After attaching the park brake actuator lever housing to the new backing plate you should install the park brake shoe. Put the new Wheel Bearing in place and fix the park brake shoe according to needs before linking the park brake cable to the actuator lever. Secure the park brake bracket bolt at 61 nm torque and join the park brake cable to the equalizer bar. Put back the tire and wheel components before lowering the vehicle.

Begin replacing the front Brake Dust Shields on 1500 series by taking out its hub and bearing parts first. Place the splash shield first and then put on the hub and bearing components. Keep the brake dust caution in mind when doing this work.

Begin replacing the 15 series and 1500 series rear disc Brake Backing Plate by releasing the parking brake then raising the car. Use appropriate support methods to avoid damage. Separate the tire and wheel by raising them and release the park brake cables' pressure through equalizer nut adjustment. Press down the locking tabs to remove the rear park brake cable from its mountings on the park brake actuator lever until you can pull it off the lever. After removing the rotor you must take off the Axle Shaft and park brake shoe before unscrewing the backing plate bolts to extract the backing plate from the axle housing flange. Install the backing plate on the axle housing flange with a correct thread preparation using brake parts cleaner plus threadlocker gm p/n 12345493 or red loctite tm #272 applied to the threads before tightening to 135 nm (100 ft. Lbs). Place the new park brake shoe and Axle Shaft into position and change the park brake shoe settings as needed. Finally attach the rotor. .thread the park brake cable back into the mounting bracket until locking tabs lock into position. Then connect the end of the cable to the park brake actuator lever. Install the tire and wheel assembly afterward and take away safety stands before lowering the vehicle and adjustment the park brake cable.

First take off the park brake actuator before disconnecting the backing plate bolts and separating the backing plate from its attachment on the axle housing flange on the 1500 series vehicle. Fit the backing plate onto axle housing flange after cleaning all traces of the previous adhesive patch. Wipe the bolt threads using brake parts cleaner and allow them to air dry before adding threadlocker gm p/n 12345493 product (Canadian P/N 10953488) to the threads. Place the backing plate bolts and tighten them to 135 nm (100 ft. Lbs.) using appropriate tools. Put back the park brake actuator then adjust both park brake shoe and brake cable to complete the process.

In order to remove the front disc Brake Dust Shields, you have to first jack up and support the vehicle, and the tire and wheel assembly. After that, go and remove which is hubbard and bearing assembly, then remove dust shields (15 Series) and dust shields (25 Series). For installation, the first installation is by installing the dust shield (25 Series), followed by dust shield (15 Series), then the hub and bearing assembly. Then, reinstall the tire and wheel assembly, remove safety stands, and lower the vehicle. Make sure that one watches out for precautions in terms of brake dust in the process.

After freeing the park brake you need to lift the vehicle and place supports under it to proceed with the replacement. Take off the tire and wheel unit before easing the park brake cable tension by pulling down on the cable near the equalizer bar and then detaching it from the equalizer. Take off the park brake cable from its mounting bracket using the locking tabs and remove the rear brake cable end from the park brake actuator lever . First unfasten the rotor from the housing then lower the Axle Shaft before taking out the park brake shoe. Using a socket and wrench remove the backing plate bolts until you can take the backing plate away from the axle housing flange. Put the backing plate on the axle housing flange first then use the backing plate nuts to fasten it at 135 nm (100 ft. Lbs.). Install the park brake shoe first and then the Axle Shaft before adjusting the park brake shoe. Install the rotor while connecting the rear park brake cable end back to the park brake actuator lever and fasten the park brake cable to its mounting bracket through the locking tabs. Complete the installation by connecting the equalizer bar to the park brake cable then put back the tire and wheel unit. Take out the safety stands and lower the vehicle while setting the park brake properly.

You must start by removing the hub and bearing assembly then proceed to replace the front disc Brake Dust Shields on the 1500 series. After installing the new dust shields you must replace the hub and bearing assembly. Follow the brake dust caution warning throughout the operation.

First, take out the park brake cable from the drum brake, using the right or left set of guidelines as required. Then, remove the Wheel Cylinder and the rear Axle Shaft, and then take out the backing plate bolts to take out the backing plate. Start by attaching the new backing plate to the rear axle housing, next install the backing plate bolts, and tighten them to 135 nm (100 ft. Lbs.). You should then put back the Wheel Cylinder and the rear Axle Shaft, and join the park brake cable by using the proper steps for its left or right side.

To replace the disc Brake Dust Shields, initially ask to lift and support the vehicle with proper lifting means. Next take away the tire and wheel assembly and then followed by the hub and bearing assembly. After that, remove the dust shields (15 series) and spill shield (25 series). For installation, start by installing dust shields (15 series), follow it with the dust shield (25 series). Following that, reinstall hub and bearing assembly as well as tire and wheel assembly. Lastly, take away the safety stands and lower the vehicle.

Install the rotor.

Take out the backing plate bolts to remove the backing plate.