Other Name: Sensor Assembly-Engine Coolant Temperature *Ite Or Black; Engine Coolant Temperature Sensor; Temperature Sensor; Temperature Sending Unit; Coolant Temperature Sensor; Engine Oil Pressure/Temperature Sensor; Computer Control Sensors
Replaces: 15369305, 25037062, 12191170, 15326388
Fits the following Buick Models:
Enclave | 2018-2021 | Avenir, Base, Essence, Preferred, Premium | 6 Cyl 3.6 L GAS
LaCrosse | 2008-2016 | Base, Convenience, CX, CXL, Leather, Premium, Super | 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 5.3 L GAS
Lucerne | 2009-2011 | CX, CXL, CXL Special Edition | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
Rainier | 2004-2007 | CXL, CXL Plus | 8 Cyl 5.3 L GAS
Regal | 2011-2017 | Base, CXL, Premium | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
Rendezvous | 2006-2007 | CX, CXL | 6 Cyl 3.5 L GAS
Terraza | 2005-2007 | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
Verano | 2012-2017 | Base, Convenience, Leather, Premium, Sport Touring, Turbo | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
Other Name: Switch Assembly, Early Fuel Evaporation Heater Engine Coolant Temperature; EFE Temperature Switch; Coolant Temperature and Early Fuel Evaporation Control Switch Kit.
Fits the following Buick Models:
Skyhawk | 1984 | Custom, Limited, T-Type | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
Skylark | 1984-1985 | Custom, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
Other Name: Switch, Coolant Temperature (Engine Unit); Switch Package, Coolant Temperature (Engine Unit); Switch, Engine Coolant Temperature ( Engine Unit)
Fits the following Buick Models:
Century | 1984-1989 | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 3.8 L GAS
Electra | 1984 | Limited, Park Avenue | 6 Cyl 4.1 L GAS
LeSabre | 1984-1985 | Collector's Edition, Custom, Limited | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS
Regal | 1984-1985 | Base, Grand National, Limited, T-Type | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS
Skylark | 1984-1985 | Custom, Limited | 4 Cyl 2.5 L GAS
Q: How to replace the Coolant Temperature Sensor on Buick LaCrosse?
A: Engine replacement of the Engine Coolant Temperature (ECT) Sensor needs an engine shutdown to safeguard against coolant leakage and injury followed by turning the ignition OFF. Before extracting the coolant temperature sensor drain an appropriate amount of coolant while simultaneously removing its electrical connector. Installation requires placement of the new coolant temperature sensor followed by tight torque to max of 22 N.m (16 lb ft). Reconnect the coolant temperature sensor electrical connector. The cooling system should undergo a complete inspection followed by necessary fluid additions before completion of the operation.
Q: How to replace the Coolant Temperature Sensor on Buick LeSabre?
A: Start by turning the ignition OFF before draining coolant so that it reaches a level lower than the ECT sensor. After disconnecting the electrical connector you must remove the ECT sensor with proper care. Use sealer GM P/N 9985253 or equivalent to cover the ECT sensor threads before installing the new component while confirming the replacement components have the proper application-specific part numbers. First tighten the ECT sensor at 20 N.m (15 lb ft) then connect the ECT harness connector to the sensor. Finally, refill the cooling system. Working with the coolant sensor requires special caution because any damage will impair the system's ability to properly operate fuel control and fuel injection functions. Perform all torque specifications correctly to prevent component damage while staying alert about the necessity of thread locking compounds and lubrication materials and corrosion inhibitors or sealants that need specified use.
Q: How to service the Coolant Temperature Sensor/Switch (For Computer) on Buick Regal?
A: The Coolant Temperature Sensor/switch (For Computer) service will be done first by making sure that the ignition is off and draining the Radiator coolant. Unplug the ect sensor electrical connector, use a 19 mm deep well socket and extension and remove the ect sensor. For installing, inserting, gently start the ect sensor into the engine and fix it with a tightening force of 30 n.m (22 lb ft). Reconnect the electrical connector and refilling the Radiator with coolant. Turn on the engine and inspect for leaks, and then visually confirm the level of coolant.