How to replace the front brake line on GMC Canyon?

Raise your vehicle and take out the front tire and wheel to start replacing the front brake hose. Thoroughly remove all dirt particles from brake hose and pipe systems. Connect the brake pipe to the hose using a back up wrench and then place a plug or cap in the brake pipe fitting to prevent fluid leakages. Remove the brake pipe end from the frame at the brake hose and verify if the retaining clip shows signs of damage; replace it with a fresh part if it is deformed or cracked. Twist off the brake hose attachment point on the frame before taking out the bolt and gaskets from the brake caliper to remove the brake hose. Take off the copper gaskets from the brake hose fastener as they might adhere to either the brake caliper or bolt. Install new copper metal gaskets to the brake hose then fasten the brake caliper bolt to the caliper while tightening the brake hose bolt to 40 nm (32 ft. Lbs.). Insert the brake hose onto the brake pipe exposed fitting but avoid any unwanted hose twisting or suspension contact. Tighten the brake hose fitting with the back up wrench to 19 nm (14 ft. Lbs.) and check that the retaining clip fits correctly before adding the new brake pipe clip. Yield the hydraulic brake system fluid then put on the wheel tire combo and let the car sink to ground level.

How to service and repair brake lines on GMC Canyon?

Start the brake pipe repair work by assembling all needed tools plus the brake pipe flaring kit part number j 45405. Install double-wall steel brake pipe safely to keep the braking system working. Open both wheel chambers using back up wrenches to remove the flaring kit's brake pipe first from the junction block then right from the axle housing. Press the flat-bladed screwdriver under the plastic brake pipe retainer locking tabs to release them and remove the part holding the rear axle brake pipe. Check the Wheel Cylinder area for defects before removing the brake pipe. Take a measurement of the brake pipe to replace plus flare length and cut the end of the new pipe square. Cut the brake pipe using the pipe cutter from brake pipe flaring kit j 45405 before choosing equal-sized brake pipe and tube nuts. Start stripping the brake pipe nylon coating using the tool from brake pipe flaring kit j 45405 without damaging the metal part. Chamfer both sides of the pipe using the de-burring tool from the brake pipe flaring kit j 45405 then install the tube nuts. Use chemical cleaners to eliminate all contaminants from the brake pipe and brake pipe flaring kit (J 45405). Open the clamp screw of the j 45405 brake pipe flaring kit before joining the proper dieset. Position both die halves. Secure the prepared pipe end into the die cage and fasten the clamping screw. Place the appropriate mandrel and pull the lever of the brake pipe flaring kit (J 45405) to make the flare before putting in the finishing cone. Check the flare for proper size before using a brake pipe bending tool to reform the new piece of pipe. During installation leave a minimum gap of 19 mm (3/4 inches) between parts that move. Twist the brake pipe onto the Wheel Cylinder until hand tight and secure it further with a wrench to 19 n.m (14 lb ft). Afterwards place and tighten the retaining bolt onto the bracket with torque settings of 20 n.m (15 lb ft). After fitting the plastic brake pipe retainer you should press the brake pipe tab closed then service and check the hydraulic brake system for leaks before lowering the vehicle into position.

OEM GMC Canyon Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Brake Lines found

View related parts
GMC Canyon Flex Hose, Driver Side Part Number: 84244994
$24.58 MSRP: $46.15
You Save: $21.57 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaced by: 85849966
- Replaces: 23209674
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Flex Hose, Rear Part Number: 87859858
$45.70 MSRP: $81.59
You Save: $35.89 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Rear Brake Crossover; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Front Passenger Side Part Number: 86517275
$22.05 MSRP: $39.38
You Save: $17.33 (45%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 85652567, 85539477
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose Part Number: 85539471
$28.60 MSRP: $51.09
You Save: $22.49 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Brake Hose
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4X | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Rear Part Number: 87859857
$28.75 MSRP: $51.35
You Save: $22.60 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Rear Brake Crossover; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose Part Number: 85580042
$27.25 MSRP: $48.66
You Save: $21.41 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Brake Hose
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4 | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Front Passenger Side Part Number: 85539475
$24.80 MSRP: $44.28
You Save: $19.48 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Front Part Number: 85539476
$21.58 MSRP: $38.54
You Save: $16.96 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Replaced by: 85722290
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Front Part Number: 85539477
$22.05 MSRP: $39.38
You Save: $17.33 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hose, Hydraulic Brake
- Position: Front
- Replaced by: 86517275
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Passenger Side Part Number: 84463252
$5.89 MSRP: $10.52
You Save: $4.63 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Flex Hose, Driver Side Part Number: 84463253
$5.80 MSRP: $10.36
You Save: $4.56 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 GMC Canyon | AT4, Denali, Elevation, Elevation Standard | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Flex Hose, Passenger Side Part Number: 84244995
$18.02 MSRP: $32.61
You Save: $14.59 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Passenger Side
- Replaced by: 85849967
- Replaces: 23209675
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Canyon | All Terrain, Base, Denali, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Canyon Flex Hose, Front Driver Side Part Number: 15882536
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 15106441
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Flex Hose, Front Driver Side Part Number: 86517274
$21.58 MSRP: $38.54
You Save: $16.96 (45%)
Product Specifications
- Other Name: Hose Assembly-Front Brake; Brake Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaced by: 85722290
- Replaces: 85539476, 85652566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Canyon | AT4, AT4X, Denali, Elevation | 4 Cyl 2.7 L GAS
View related parts
GMC Canyon Flex Hose, Front Driver Side Part Number: 15882533
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 15101603
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Flex Hose, Front Passenger Side Part Number: 15882534
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 15101604
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Flex Hose, Front Passenger Side Part Number: 15882535
Product Specifications
- Other Name: Hose Assembly-Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 15106440
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Flex Hose Part Number: 10363839
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Canyon Flex Hose Part Number: 22894844
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Rear
- Replaces: 25928296
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2012 GMC Canyon | SLE, SLT, WT | 4 Cyl 2.9 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Canyon Flex Hose Part Number: 22894845
Product Specifications
- Other Name: Hose, Hydraulic Brake; Brake Hose; Piston
- Position: Rear
- Replaces: 25928297
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2012 GMC Canyon | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS

| Page 1 of 2 |Next >

1-20 of 26 Results

GMC Canyon Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Canyon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Canyon Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The function of the Brake Line in GMC Canyon is to permit the braking fluid from the master cylinder to go to the brake caliper pistons, which will allow the hydraulic braking system to work. Steel brake lines are notorious for rusting and getting damaged through impact and this can make it difficult for the hydraulic fluid to flow through and build up the required pressure required. Brake hoses also degrade mechanically and chemically which may also lead to physical and internal damages that will compromise the brake system. When replacement is necessary, the pre bent brake line kits and the corrosion resistant stainless steel hoses are easy to fix. Most Touring cars come fitted with flexible rubber hoses and replacing this with braided stainless steel hoses give the driver a much better pedal feel and reaction for high speed dynamic man oeuvres.

GMC Canyon Brake Line Parts and Q&A

Flex Hose, Front Driver Side
15882536
Q: How to replace the front brake line on GMC Canyon?
A:
Raise your vehicle and take out the front tire and wheel to start replacing the front brake hose. Thoroughly remove all dirt particles from brake hose and pipe systems. Connect the brake pipe to the hose using a back up wrench and then place a plug or cap in the brake pipe fitting to prevent fluid leakages. Remove the brake pipe end from the frame at the brake hose and verify if the retaining clip shows signs of damage; replace it with a fresh part if it is deformed or cracked. Twist off the brake hose attachment point on the frame before taking out the bolt and gaskets from the brake caliper to remove the brake hose. Take off the copper gaskets from the brake hose fastener as they might adhere to either the brake caliper or bolt. Install new copper metal gaskets to the brake hose then fasten the brake caliper bolt to the caliper while tightening the brake hose bolt to 40 nm (32 ft. Lbs.). Insert the brake hose onto the brake pipe exposed fitting but avoid any unwanted hose twisting or suspension contact. Tighten the brake hose fitting with the back up wrench to 19 nm (14 ft. Lbs.) and check that the retaining clip fits correctly before adding the new brake pipe clip. Yield the hydraulic brake system fluid then put on the wheel tire combo and let the car sink to ground level.
Flex Hose, Front Passenger Side
15882535
Q: How to service and repair brake lines on GMC Canyon?
A:
Start the brake pipe repair work by assembling all needed tools plus the brake pipe flaring kit part number j 45405. Install double-wall steel brake pipe safely to keep the braking system working. Open both wheel chambers using back up wrenches to remove the flaring kit's brake pipe first from the junction block then right from the axle housing. Press the flat-bladed screwdriver under the plastic brake pipe retainer locking tabs to release them and remove the part holding the rear axle brake pipe. Check the Wheel Cylinder area for defects before removing the brake pipe. Take a measurement of the brake pipe to replace plus flare length and cut the end of the new pipe square. Cut the brake pipe using the pipe cutter from brake pipe flaring kit j 45405 before choosing equal-sized brake pipe and tube nuts. Start stripping the brake pipe nylon coating using the tool from brake pipe flaring kit j 45405 without damaging the metal part. Chamfer both sides of the pipe using the de-burring tool from the brake pipe flaring kit j 45405 then install the tube nuts. Use chemical cleaners to eliminate all contaminants from the brake pipe and brake pipe flaring kit (J 45405). Open the clamp screw of the j 45405 brake pipe flaring kit before joining the proper dieset. Position both die halves. Secure the prepared pipe end into the die cage and fasten the clamping screw. Place the appropriate mandrel and pull the lever of the brake pipe flaring kit (J 45405) to make the flare before putting in the finishing cone. Check the flare for proper size before using a brake pipe bending tool to reform the new piece of pipe. During installation leave a minimum gap of 19 mm (3/4 inches) between parts that move. Twist the brake pipe onto the Wheel Cylinder until hand tight and secure it further with a wrench to 19 n.m (14 lb ft). Afterwards place and tighten the retaining bolt onto the bracket with torque settings of 20 n.m (15 lb ft). After fitting the plastic brake pipe retainer you should press the brake pipe tab closed then service and check the hydraulic brake system for leaks before lowering the vehicle into position.